聚氯乙烯搪塑粉料用低挥发损失率复合热稳定剂的制备及性能
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

国家973计划项目(2012CB821505);吉林省科技发展计划重大项目(20150301002GX);山东省自然科学基金重点项目(ZR2015QZ05)


Preparation and Property of Compound Heat Stabilizer for PVC Slush Molding Powders with Low Volatilization Loss Rate
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    以市售液态钙锌稳定剂T1为主原料,按一定比例复配偏苯三甲酸三辛酯以保护钙/锌皂盐的活性,并将该混合液于140 ℃恒温蒸发120 min,使原液态钙锌稳定剂中稳定性差的助剂得以挥发,得到适用于聚氯乙烯(PVC)搪塑粉料的复合热稳定剂T2,进而制备PVC搪塑表皮,并测试其挥发损失率和热稳定性等性能。结果表明,与市售液态钙锌稳定剂T1相比,添加了自制稳定剂T2的PVC搪塑表皮的挥发损失率显著降低,同时表皮的热稳定性和抗热老化性能都得到改善。

    Abstract:

    Based on the liquid calcium zinc stabilizer T1 which is commercially available, trioctyltrimellitate in a certain ratio was added into the stabilizer to protect the activity of zinc and calcium soap. The liquid mixture was kept in an oven at 140 ℃ for 2 h to get the compound heat stabilizer T2 for polyvinyl chloride (PVC) slush molding powders, in which some additives with poor thermostability evaporated out of the liquid mixture. Then PVC slush molded skins were manufactured and their performances were studied. The results show that the selfmade compound stabilizer T2 can not only lower the volatilization loss rate, but also improve the thermostability and antiaging property of PVC slush molded skins compared with the stabilizer T1.

    参考文献
    相似文献
    引证文献
引用本文

赵亚如, 高琳琳, 陈娟, 姚卫国, 贾玉玺.聚氯乙烯搪塑粉料用低挥发损失率复合热稳定剂的制备及性能[J].高分子材料科学与工程,2017,33(2):172-176. Yaru Zhao, Linlin Gao, Juan Chen, Weiguo Yao, Yuxi Jia. Preparation and Property of Compound Heat Stabilizer for PVC Slush Molding Powders with Low Volatilization Loss Rate[J]. Polymer Materials Science & Engineering,2017,33(2):172-176.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2017-02-24
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司