超细NaHCO3的制备及在聚丙烯微孔发泡材料中的应用
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

国家自然科学基金资助项目(11372108);湖南省高校创新平台开放基金(14K032);湖南省科技计划(14JJ5021);湖南省研究生科研创新项目(CX2015B561)


Preparation of Ultrafined NaHCO3 and Used in PP Microcellular
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    选用价廉无毒的碳酸氢钠(NaHCO3)作为发泡剂,利用反溶剂重结晶法进行细化,成功地制备出超细NaHCO3粒子。最佳制备条件为:使用10%质量分数的NaHCO3,蒸馏水与无水乙醇体积比1∶14,搅拌速度1100 r/min,制备温度-5 ℃,入料速度1 mL/min。纳米粒度分析仪测试表明NaHCO3平均尺寸为143.2 nm,尺寸分布非常窄。将超细NaHCO3添加到聚丙烯(PP)中进行微孔发泡,使用扫描电镜观察并使用Nano Measurer分析泡孔尺寸,表明当NaHCO3用量为4.5 phr时,其泡孔平均尺寸低至0.47 μm,泡孔尺寸标准方差仅为0.16 μm,低于任何文献报道值。力学性能较优,其中拉伸强度下降了9.6%,而冲击强度提高了47.8%,弯曲强度提高了20.2%。这种使用普通注塑机获得高质量低成本的微孔发泡材料,对微孔材料的制备和应用有一定的意义。

    Abstract:

    Cheap and nontoxic sodium bicarbonate (NaHCO3) was chosen as blowing agent, and ultrafined NaHCO3 particles were successfully prepared by anti-solvent recrystallization method. When the mass concentration of NaHCO3 is 10%, the volume ratio of water and ethanol is 1∶14, the speed of stirring is 1100 r/min, the preparation temperature is -5 ℃, the feed rate is 1 mL/min, the optimal preparation conditions are determined. The average particles size of ultrafined NaHCO3 is 143.2 nm along with a narrow size distribution which was measured by laser particle size analyzer. The ultrafined NaHCO3 was mixed with PP to prepare microcellular PP, and SEM was used to observe these microcellulars and Nano Measurer software was applied to analyze these cells size. The results show that when the NaHCO3 amount is 4.5 phr, the average size is 0.47 μm, the cell size standard deviation is only 0.16 μm, lower than any reported literature. The microcellular PP remains excellent mechanical properties than the unfoamed, the impact strength and the flexural modulus enhances 47.8% and 20.2% respectively, whereras the tensile strength slightly drops 9.6%. Excellent cell structure, good properties and cheap microcellular PP was successfully prepared by ordinary injection molding machine, which has a significant effect on the development and application of microcellular in the future.

    参考文献
    相似文献
    引证文献
引用本文

石璞, 陈浪, 姜黎, 伍文宗, 孙鹏, 刘跃军.超细NaHCO3的制备及在聚丙烯微孔发泡材料中的应用[J].高分子材料科学与工程,2017,33(4):87-93. Pu Shi, Lang Chen, Li Jiang, Wenzong Wu, Peng Sun, Yuejun Liu. Preparation of Ultrafined NaHCO3 and Used in PP Microcellular[J]. Polymer Materials Science & Engineering,2017,33(4):87-93.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2017-04-21
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司