聚乙烯醇缩甲醛泡沫塑料负压渗水材料的改性与性能
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

国家高技术研究发展计划(2013AA102901)


Morphology and Properties of Modified Polyvinyl Formal
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    为研究硅烷偶联剂KH550、聚硫橡胶(PR)对负压渗水材料聚乙烯醇缩甲醛泡沫塑料(PVFM)性能的影响,以聚乙烯醇、甲醛为原料,盐酸为催化剂,制备一系列改性PVFM,并测试其形貌、渗水性和力学性能等。结果表明,KH550改性PVFM 可提高其饱和导水率,PR则表现相反;2种改性PVFM 在-5kPa下累计入渗量比未改性PVFM 少,且均随用量增加而降低;2种改性剂均对PVFM 发泡点有较大程度提升;2%KH550样品密度降低43.5%,1.5%KH550样品硬度提升64.6%;5%PR改性PVFM 硬度达最大值71,PR改性PVFM 断裂伸长率提升29.7%~46.7%;KH550改性的PVFM 孔径增大,弯曲度更简单,导致硬度减小、导水率增大;PR改性PVFM 立体网状结构更致密,加之-SH疏水基团增加,导致PVFM 输水能力、负压渗水性降低。综合考虑,建议使用.0%PR改性PVFM 可改善PVFM 负压渗水性能与力学性能,提高其工作稳定性。

    Abstract:

    To reveal the effect of silane coupling agent KH550 and polysulfide rubber(PR) on the properties of negative-pressured porous material-PVFM, a series of samples compound of polyvinyl alcohol (PVA), formaldehyde and hydrochloric acid were modified. The morphology, water permeability and mechanical property were investigated. The results show that the saturated hydraulic conductivity of polyvinyl formal (PVFM) samples modified by KH550 is higher than that of the unmodified ones, but samples modified by PR show reveres variations. The cumulative infiltration of modified PVFM is lower under -5 kPa irrigated conditions, and it could be reduced with the increasing of modifying agent. There is a significant rise in blow point with adding two kinds of modifying agents. The density of modified samples with 2% KH550 reduces 43.5%. Samples modified with 1.5% KH550 have 64.6% rise in Shore hardness, and it is 71 with 5%PR. Polysulfide rubber can effectively improve the elongation at break of PVFM by 29.7%~46.7%. The bumpy and uneven surface of modified samples with KH550 is embeded with tiny holes and cracks, which can result in decrease of hardness and promotion of hydraulic conductivity. The three-dimensional network of samples modified with PR is more compact. It leads to diminution of pore diameter internal and increase of curvature. Coupled with increase of hydrophobic grouping (-SH), the water-carrying capacity and cumulative infiltration under negative-irrigation conditions are reducing. It is suggested to use 5.0% PR to modify PVFM, which could improve water permeability and mechanical property of PVFM to enhance stability of negative-pressured seepage device.

    参考文献
    相似文献
    引证文献
引用本文

丁亚会,丛 萍,龙怀玉.聚乙烯醇缩甲醛泡沫塑料负压渗水材料的改性与性能[J].高分子材料科学与工程,2017,33(6):105-112. Yahui Ding, Ping Cong, Huaiyu Long. Morphology and Properties of Modified Polyvinyl Formal[J]. Polymer Materials Science & Engineering,2017,33(6):105-112.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2017-06-21
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司