预交联法制备海藻酸钠复合微球及其缓释性能
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

江苏省“六大人才高峰”项目(XCL-036)


Preparation and Sustained Release Properties of Sodium Alginate Composite Microspheres with Pre-Crosslinking Method
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    采用预交联法制备海藻酸钠(SA)/凹土(ATP)复合微球(PCM)以克服常规制备方法导致微球交联不均匀的缺陷,从而改善微球的缓释性能。将ATP先与Ca2+ 进行部分离子交换制备Ca2+-ATP,然后在与SA 复合过程中同时进行预交联形成交联密度有所提高的微球内核,再采用滴注法制备该复合微球。利用红外光谱、扫描电镜和电子照片对微球结构和形貌进行表征,考察了Ca2+ 浓度对PCM 力学强度、溶胀率、载药和缓释性能的影响。结果表明,PCM 在1h的累计释放率由预交联前的68%降为50%,显著改善了微球的“突释”。释放动力学研究表明,微球的释药可用Ritger-Peppas方程很好地拟合,释药速率受骨架溶蚀和药物扩散双重控制。

    Abstract:

    The pre-crosslinking method was used to prepare sodium alginate(SA)/attapulgite(ATP) composite microspheres(PCM) to overcome the nonhomogeneous crosslinking caused by the conventional method, and further improve the sustained release properties of the microspheres. Ca2+-ATP was prepared with ATP exchanged with Ca2+, and then composited with SA to form the enhanced core of PCM with the pre-crosslinked occurred simultaneity. The morphology and structure of the microspheres were characterized by FT-IR, SEM and electronic photos. The effect of Ca2+ content on mechanical strength,swelling ratio,drug loading and sustained release properties of PCM was investigated. The results show that the burst release of PCM in the first 1 h decreases from 68% to 50% after pre-crosslinked. The drug release process of microspheres is better fitted by the Ritger-Peppas model and the rate of drug release is governed by both diffusion and swelling mode.

    参考文献
    相似文献
    引证文献
引用本文

陶 倩,吴 洁,张海江.预交联法制备海藻酸钠复合微球及其缓释性能[J].高分子材料科学与工程,2017,33(8):145-150. Qian Tao, Jie Wu, Haijiang Zhang. Preparation and Sustained Release Properties of Sodium Alginate Composite Microspheres with Pre-Crosslinking Method[J]. Polymer Materials Science & Engineering,2017,33(8):145-150.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2017-08-24
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司