基于选择性激光烧结聚己内酯/蛋壳多孔支架的制备和表征
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

国家自然科学基金资助项目(51365038);江西省科技支撑计划项目(20122BBE500044);江西省高校科技落地计划项目(KJLD12058);江西省教育厅科学技术研究项目(GJJ150153)


Characterization of Porous Scaffolds Based on Polycaprolactone/Eggshell Preparedvia Selective Laser Sintering
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    以聚己内酯(PCL)和鸡蛋壳粉末(ES)为原材料,采用选择性激光烧结技术制备纯PCL支架和PCL/ES混合材料支架。通过显微镜观察了支架形貌,测定了各组支架的孔隙率和压缩强度。结果表明ES的加入能使支架的压缩强度有所提高,但同时孔隙率稍有降低,填充速度为1380~1880 mm/min时PCL/ES支架能取得较高的孔隙率(80%)和压缩强度(8.28MPa),达到松质骨的要求(孔隙率≥70%,压缩强度≥8.2MPa);差示扫描量热分析和热重分析结果表明ES的加入改善了复合支架的结晶性能和热稳定性;对粉末和支架的X射线衍射和衰减全反射傅里叶变换红外光谱检测证实了ES的成分和选择性激光烧结工艺没有破坏原材料的分子官能团;用MTT比色法测定了支架毒性试验,结果表明PCL/ES复合支架无明显毒性且具有良好的生物相容性。因此,选择性激光烧结制备的PCL/ES支架具有很好的外形可塑性和空隙结构,其良好的力学性能和生物相容性使其有望在骨组织工程支架中得到应用。

    Abstract:

    The scaffolds were fabricated from polycaprolactone (PCL)/eggshell (ES) composite using selective laser sintering (SLS) technique. The micro-structure of the scaffolds was observed using microscope. The porosity and compressive strength of the scaffolds were measured in vitro. The results show that the addition of ES can make the compression strength of the scaffolds increase, but the porosity decreases slightly. PCL/ES scaffolds could get high porosity (80%) and compressive strength (8.28 MPa) with the filling speed at 1380~1880 mm/min, which achieve the requirements of cancellous bone porositymore than 70%, the compression strength not less than 8.2 MPa. Thermal analysis shows that the addition of ES improves the crystallization properties and thermal stability of PCL. FT-IR spectra of the scaffolds indicate that processing does not change the functional groups compared to raw materials. The results of MTT colorimetric assay show that the PCL/ES composite scaffolds have good biocompatibility.In conclusion, PCL/ES scaffolds fabricated by SLS have good strength and excellent internal and external structure, indicating that they have great potential as bone tissue engineering scaffolds based on mechanical properties and biocompatibility.

    参考文献
    相似文献
    引证文献
引用本文

张平生,辛 勇,曹传亮,刘 宇.基于选择性激光烧结聚己内酯/蛋壳多孔支架的制备和表征[J].高分子材料科学与工程,2017,33(10):114-120. Pingsheng Zhang, Yong Xin, Chuanliang Cao, Yu Liu. Characterization of Porous Scaffolds Based on Polycaprolactone/Eggshell Preparedvia Selective Laser Sintering[J]. Polymer Materials Science & Engineering,2017,33(10):114-120.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2017-10-29
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司