水性聚氨酯膜的制备及在超纤革中的应用
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

国家科技支撑项目(2014BAE09B00);天津市应用基础与前沿技术研究计划重点项目(15JCZDJC38500);天津市科技计划(14TXGCCX00014)


Preparation of Waterborne Polyurethane Membrane and Its Applications in Microfiber Synthetic Leather
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    以水性聚氨酯(WPU)为聚合物,采用物理机械发泡的方法制备WPU 膜,系统研究了成膜温度对WPU 膜形态结构和性能的影响规律。结果表明,当成膜温度低于100 ℃时,所制备WPU 膜的泡孔密度、表面孔孔径、平均孔径、结晶度、透气量、透湿率、断裂强度和断裂伸长率等均随成膜温度的升高而增大。其中,当成膜温度为80℃时,膜具有最佳的性能。随着成膜温度进一步升高,膜的表面出现裂纹,透气量和透湿率增加,而断裂强度和断裂伸长率显著减小。在此基础上,经干法移膜技术制备的WPU 超纤革达到了成品等级的A类产品。

    Abstract:

    The waterborne polyurethane (WPU) membrane using WPU as polymer was prepared through physical-mechanical foaming. The effects of membrane-forming temperature on the structure and performance of WPU membranes were investigated. The results show that the foam density, surface pore size, mean pore size, crystallinity, air permeability, water vapor permeability, tensile strength and elongation at break of the obtained WPU membrane increase with an increase from 40 ℃ to 80 ℃ in membrane-forming temperature. When membrane-forming temperature is 80 ℃, the permeability of WPU membrane obtained is optimal. Further, the WPU membranes with the increase of membrane-forming temperature exhibit crack structure. The air permeability and water vapor permeability of the obtained WPU membrane increase with the increase of membrane-forming temperature, and the tensile strength and elongation at break observably decrease with the increase of membrane-forming temperature. On this basis, the WPU microfiber synthetic leather made by dry process has reached the level of A.

    参考文献
    相似文献
    引证文献
引用本文

赵宝宝,钱 幺,钱晓明,范金土,宋 兵.水性聚氨酯膜的制备及在超纤革中的应用[J].高分子材料科学与工程,2017,33(10):135-140. Baobao Zhao, Yao Qian, Xiaoming Qian, Jintu Fan, Bing Song. Preparation of Waterborne Polyurethane Membrane and Its Applications in Microfiber Synthetic Leather[J]. Polymer Materials Science & Engineering,2017,33(10):135-140.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2017-10-29
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司