氯化锌催化合成含硅芳炔树脂
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:


Synthesis of Silicon-Containing Arylacetylene Resin Catalyzed by ZnCl2
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    以二乙炔基苯、双(二甲氨基)二甲基硅烷为原料,乙腈为溶剂,通过氯化锌催化实现单步硅烷化合成含硅芳炔树脂。研究结果表明,乙腈做溶剂,二乙炔基苯与双(二甲氨基)二甲基硅烷投料比为9∶8(摩尔比),ZnCl2相对于炔过量0.65倍,回流反应11 h效果最佳,收率高达90%以上;制备的含硅芳炔树脂在室温下呈流动状态,加工性能良好,加工温度为40~180 ℃,加工窗口为140 ℃;固化后的含硅芳炔树脂,在N2气氛下热分解5%时的温度(Td5)为587 ℃。

    Abstract:

    A novel one-step synthesis of silicon-containing arylacetylene resin (PSA) was developed via the direct silylation of diethynylbenzene (DEB) and bis(dimethylamino)dimethylsilane. The results show that the optimum reaction conditions: acetonitrile as solvent, mole feed ratio of alkyne and amino is 9∶8, the amount of zinc overdose 0.65 times compared with alkynes, and reaction time 11 h. The processing temperature is from 40 ℃ to 180 ℃, and the processing window is about 140 ℃. The reaction yield reaches up to 90%. The properties of the resulting resin were investigated. The resin is in a state of flow and has good processing performance at room temperature. The cured resin performs good heat resistance, the decomposition temperature at 5% mass loss in nitrogen is 587 ℃.

    参考文献
    相似文献
    引证文献
引用本文

姜 欢, 邓诗峰, 阮湘政.氯化锌催化合成含硅芳炔树脂[J].高分子材料科学与工程,2017,33(11):18-21. Huan Jiang, Shifeng Deng, Xiangzheng Ruan. Synthesis of Silicon-Containing Arylacetylene Resin Catalyzed by ZnCl2[J]. Polymer Materials Science & Engineering,2017,33(11):18-21.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2017-11-22
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司