废旧胶粉异向双螺杆挤出机连续脱硫挤出传热模拟及实验
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:


Heat Transfer Simulation and Experiment of Continuous Desulphurization Extrusion of Ground Tire Rubber in Counter Rotating Twin Extruder
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    常压连续脱硫塑化机是目前再生胶行业正在推广的新型脱硫生产方式。针对其中的一种———异向双螺杆挤出机,文中应用Workbench对胶粉在螺杆内脱硫过程进行传热模拟,统计各C型室单元温度分布和温度累计曲线。结果表明,胶粉导热系数小,传热性能很差,由预热区到高温区的温度累计曲线斜率逐渐一致,温度分布逐渐均匀。为了验证所建模型和模拟结果的合理性,将模拟结果与实际生产过程中挤出机出料温度作对比,模拟结果误差在16%左右,验证了此模拟分析的合理性。

    Abstract:

    It is a new type of desulfurization method which is being promoted in the reclaimed rubber industry by using the normal pressure continuous desulphurization plastic mechanism. In this paper, the heat transfer process of ground tire rubber (GTR) in the one of them counter rotating twin screw extruder was simulated by Workbench, the temperature distribution and temperature cumulative curves of different C chamber of were added up.The results show that the coefficient of thermal conductivity of rubber powder is small and the heat transfer performance of rubber powder is very poor, and temperature cumulative curve slope is consistent gradually and the temperature distribution is gradually uniform in the preheating zone to high temperature zone. In order to verify the rationality of the model and the simulation results, compared with the simulation results and the experimental results of powder temperature, the error of simulation is about 16% and the simulation model is reasonable.

    参考文献
    相似文献
    引证文献
引用本文

杨晓彤,任冬云,张立群.废旧胶粉异向双螺杆挤出机连续脱硫挤出传热模拟及实验[J].高分子材料科学与工程,2018,34(3):100-105. Xiaotong Yang, Dongyun Ren, Liqun Zhang. Heat Transfer Simulation and Experiment of Continuous Desulphurization Extrusion of Ground Tire Rubber in Counter Rotating Twin Extruder[J]. Polymer Materials Science & Engineering,2018,34(3):100-105.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2018-04-03
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司