基于选区激光烧结工艺的多孔尼龙制备及性能
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

国家高技术研究发展计划(863计划)资助项目(2015AA042503)


Fabrication Process and Properties of Porous Polyamide Produced by Selective Laser Sintering
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    提出一种基于选区激光烧结的多孔材料成型方法,利用增材制造技术控形、控性的优势,实现多孔材料结构与功能的可控设计。采用尼龙与水溶性致孔剂NaCl为原材料,通过改变致孔剂含量和工艺参数,实现多孔材料的孔隙率、渗透性及力学性能的可控调节。实验结果表明,多孔材料的孔隙率、渗透性随着致孔剂含量的增大而增大;在相同的致孔剂含量下,其孔隙率和渗透性随着激光能量密度的增加呈下降趋势,分层厚度增加,孔隙率和渗透性明显增加;制备的多孔材料最高孔隙率达到59%,渗透率达0.312mL/(mm2·s),弯曲强度可达44MPa。以陶瓷高压注浆成型多孔树脂模具为例,开展多孔材料的功能验证,获得厚度为10mm、含水率为20%的陶瓷坯体,为该模具的快速制造提供了一种新手段。

    Abstract:

    A peculiar method based on selective laser sintering(SLS) to fabricate porous materials was proposed, which utilized the characteristic of structure and property control derived from additive manufacturing(AM) to realize the controllable structure and function design. The composite powders used for SLS were prepared by mechanically mixing polyamide12 (PA12) with the water-soluble pore-foaming agent (NaCl). The controllable porosity, permeability and mechanical property were achieved by changing NaCl contents and processing parameters. Experiment results show the porosity and permeability both increase with increasing NaCl contents. The maximum porosity, permeability and flexural strength reach 59%, 0.312 mL/(mm2·s) and 44 MPa, respectively. The application research is performed on the porous PA mould for ceramic pressure slip casting. A green body with the wall thickness up to 10 mm and moisture content of 20% is obtained, which can meet basic requirements of slip casting process. This work offers an alternative approach for the rapid manufacturing of porous resin moulds and personalized customization of porcelain products.

    参考文献
    相似文献
    引证文献
引用本文

彭 刚,晏梦雪,田小永,李涤尘.基于选区激光烧结工艺的多孔尼龙制备及性能[J].高分子材料科学与工程,2018,34(3):145-150. Gang Peng, Mengxue Yan, Xiaoyong Tian, Dichen Li. Fabrication Process and Properties of Porous Polyamide Produced by Selective Laser Sintering[J]. Polymer Materials Science & Engineering,2018,34(3):145-150.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2018-04-03
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司