碳化钨粉末注射成形一步热脱脂的脱脂动力学
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

江苏省产学研联合创新资金-前瞻性联合研究项目(BY2016029-06)


Degreasing Kinetics of One-Step Thermal Debinding of Tungsten Carbide Powder for Feedstock Injection Molding
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    采用热重分析法测定了在氮气气氛中5℃/min、10℃/min、15℃/min和20℃/min不同升温速率下的石蜡、保形聚合物(PP与HDPE的混合物)、石蜡/保形聚合物和碳化钨(WC-10%Ni)粉末注射成形专用料的热解过程,采用Kissinger法和Flynn-Wall-OZAWA法对4种专用料的热分解动力学进行分析,并用Coats-Redfern研究反应级数。结果表明,用Kissinger法分析不能很好地反映混合物的复杂的热解过程,不能支持碳化钨粉末注射成形一步热脱脂的工艺制定。用Flynn-Wall-OZAWA法分析,石蜡的热分解活化能在59~72kJ/mol,保形聚合物的热分解活化能在143~252kJ/mol,石蜡/保形聚合物的热分解活化能在60~240kJ/mol和WC-10%Ni的专用料的热分解活化能在93~220kJ/mol。用Coats-Redfern法分析,石蜡与保形聚合物的热解可用一级反应来描述,而石蜡/保形聚合物与WC-10%Ni的专用料的热解则适用3个连续一级反应来描述。

    Abstract:

    In this paper, the decomposition process of paraffin waxes, conformal polymers (mixtures of PP and HDPE), paraffin / conformal polymerization (PP/HDPE) and tungsten carbide (WC-10%Ni) Ni powder injection molding feedstock was analyzed by thermogravimetric methodin nitrogen at four different heating rates (5 ℃/min, 10 ℃/min, 15 ℃/min and 20 ℃/min). The thermal decomposition kinetics of these four materials was analyzed by Kissinger method and Flynn-Wall-OZAWA method, and the reaction order was studied by Coats-Redfernformulation. The results show that the Kissinger method does not reflect the complex pyrolysis process of the mixture welland can not support the one-step thermal debinding process of tungstencarbide powder for feedstock injection molding. Determined by Flynn-Wall-OZAWA method, the pyrolysis activation energy of paraffin wax, conformal polymer, paraffin/conformal polymer and tungsten carbide (WC-10%Ni) nickel powder injection molding feedstock is respectively 59~72 kJ/mol, 143~252 kJ/mol, 60~240 kJ/mol and 93~220 kJ /mol respectively. The pyrolysis of paraffin and conformal polymers can be described by the first order reaction,while the mixture of paraffin/conformal polymer and WC-10%Ni is described by three successive first-order reactions.

    参考文献
    相似文献
    引证文献
引用本文

刘春林,史安康,吴 盾,陆 颖,张钱鹏,刘 刚.碳化钨粉末注射成形一步热脱脂的脱脂动力学[J].高分子材料科学与工程,2018,34(7):107-113. Chunlin Liu, Ankang Shi, Dun Wu, Ying Lu, Qianpeng Zhang, Gang Liu. Degreasing Kinetics of One-Step Thermal Debinding of Tungsten Carbide Powder for Feedstock Injection Molding[J]. Polymer Materials Science & Engineering,2018,34(7):107-113.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2018-08-10
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司