一种差速双螺杆非充满熔体输送模型
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

国家自然科学基金资助项目(11272093)


A Kind of Conveying Model of Partially Filled Fluid in a Non-Twin Screw Channel
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    自主研制了可切换螺杆转速比的机筒全程透明的同向双螺杆挤出仪器,可分别进行等速及差速双螺杆挤出可视化实验研究。制备了羧甲基纤维素钠溶液作为加工流体,观察不同计量加料情况下,螺杆构型及双螺杆转速对流体输送行为的影响,提出了全新的包括正位移和拖曳流的部分充满流体输送模型。实验表明,在非充满情况下,流体输送的拓扑路线不同,与等速双螺杆相比,物料在差速双螺杆左右螺槽内充满度存在非对称现象,上下啮合区存在较大的堆积现象。2种螺杆构型输送机理相似,均存在拖曳流、正位移输送及螺杆机筒间隙漏流。在非充满情况下,初步建立了差速同向自洁双螺杆的流体输送解析理论,得到了不同情况下充满度计算公式。当产量一定时,随着螺杆转速的增加,螺槽充满度下降,漏流增大,拖曳流量减少,而正位移量增加。

    Abstract:

    A novel co-rotating extrusion device was self-developed, where the whole barrel was transparent and the speed ratio output of one screw to another screw could be adjusted to 1∶1 or 2∶1. The visualization experiments were conducted to study the extrusion processes using the speed ratios of screw pairs of 1∶1 and 2∶1. A kind of colored sodium carboxymethyl cellulose was prepared as a test fluid, and its rheological properties were characterized. Effect of the screw configurations and screw speed on the conveying behavior was observed when the different feed rate was used. A new conveying model considering the positive displacement and drag flow was proposed. The experimental results show that the topologies of fluid conveying are quite different when the screw channel is partially filled. Compared with the twin screw configuration, the configuration with the speed difference in screw pair finds the asymmetry effect of fill degrees in the left and right channels, and the larger pile-up of fluid appears in the top and lower intermeshing regions. The both configurations share the similar conveying mechanism, including drag flow, positive displacement transport and the leakage between the barrel and the screw tip. Under the condition of partial fill, the analytical equations are derived for the first time regarding fluid conveying in co-rotating non-twin screw channels, and then the fill degrees under different operations can be obtained. When the output remains unchanged, with the increase of screw speed, the fill degree decreases along with the increase of leakage and the positive displacement transport in contrast to the decrease of drag flow.

    参考文献
    相似文献
    引证文献
引用本文

喻慧文, 吴宏武, 徐百平, 周延辉, 蓝叶青, 王玫瑰.一种差速双螺杆非充满熔体输送模型[J].高分子材料科学与工程,2018,34(8):88-95. Huiwen Yu, Hongwu Wu, Baiping Xu, Yanhui Zhou, Yeqing Lan, Meigui Wang. A Kind of Conveying Model of Partially Filled Fluid in a Non-Twin Screw Channel[J]. Polymer Materials Science & Engineering,2018,34(8):88-95.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2018-09-05
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司