表面活性剂对Ti-6Al-4V金属注射成形喂料相容性的影响
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

江苏省产学研联合创新资金-前瞻性联合研究项目(BY2016029-06);江苏省产业前瞻与共性关键技术-竞争项目(BE2017059)


Effect of Surfactants on Compatibility of Ti-6Al-4V Metal Injection Molding Feedstock
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    为研究不同的表面活性剂对Ti-6Al-4V金属注射成形(MIM)喂料相容性的影响,对喂料分组添加相同含量的硬脂酸(SA)、司盘80(Span 80)和乙撑双硬脂酸酰胺(EBS),通过润湿角实验、流变实验、力学性能实验和断面形貌分析选择适合的表面活性剂。结果表明,添加EBS黏结剂的湿润角为37.6°,具有较好的润湿效果;含有EBS的喂料具有较低的屈服应力,温度的变化对其流变性能有较小的影响;含有EBS的喂料具有较高的剪切敏感性和最高的综合流变学因子值,并具有较高的抗弯强度,断裂面上存在较少的“窝状”和裸露的Ti-6Al-4V粉末。

    Abstract:

    In order to study the effect of surfactants on compatibility of Ti-6Al-4V metal injection molding feedstock, stearic acid (SA), sorbitan oleate (Span80) and ethylene bis-stearamide (EBS) with the same content were added to the feedstock respectively. The wetting angle test, rheological properties analysis, mechanical property studies and fracture surface analysis were carried out to choose the appropriate surfactants. The results show that the wetting angle of binder containing EBS is 37.6°, and it has better wetting effect. The feedstock containing EBS exhibits lower yield stress and the change of temperature has slight influence on its rheological properties. The feedstock containing EBS shows higher shear sensitivity and the highest value of a general rheological index, and higher flexural strength is observed. Fewer “nests” and barer Ti-6Al-4V powder exist on the fracture surface.

    参考文献
    相似文献
    引证文献
引用本文

刘春林, 张钱鹏, 陆 颖, 史安康, 刘 钢, 吴 盾.表面活性剂对Ti-6Al-4V金属注射成形喂料相容性的影响[J].高分子材料科学与工程,2018,34(9):96-100. Chunlin Liu, Qianpeng Zhang, Ying Lu, Ankang Shi, Gang Liu, Dun Wu. Effect of Surfactants on Compatibility of Ti-6Al-4V Metal Injection Molding Feedstock[J]. Polymer Materials Science & Engineering,2018,34(9):96-100.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2018-11-08
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司