冷冻干燥制备聚酰亚胺气凝胶微观形态的调控
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

国家自然科学基金资助项目(51353002,51633004);高分子材料工程国家重点实验室课题(sklpme2014-2-04)


Control of Microstructure of Polyimide Aerogel Prepared by Freeze-Drying
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    将一定浓度的水溶性聚酰胺酸盐(PAAS)溶液先通过冷冻干燥制备PAAS气凝胶,再经热酰亚胺化得到聚丙烯酰胺(PI)气凝胶。通过调控PAAS溶液固含量、冻干溶剂组成及聚酰亚胺链结构,成功实现了对PI气凝胶微观形态的调控。研究发现,以纯水作为冻干溶剂,得到孔径为110μm 左右的蜂窝状结构,随着固含量的增加,孔壁厚度增加。以叔丁醇替代部分水作为冻干剂,随着叔丁醇含量增加,孔洞尺寸先减小后增加,在水和叔丁醇共晶点(20%)附近孔洞尺寸最小。当叔丁醇质量分数为50%时,所得PI链结构刚性不同,其微观形态也不同。进一步研究链柔顺性和微观形态对气凝胶压缩性能的影响发现,气凝胶微观形态对其抗压能力起主要作用。

    Abstract:

    Polyamide acid salts (PAAS) aerogel was prepared by freeze-drying with a certain concentration of water-soluble PAAS solution, and PI aerogel was obtained by thermal imidization. By changing the solid content of PAAS solution, the composition of freeze-dried solvent and the structure of polyimide chain, the microstructure regulation of PI aerogel was successfully realized. It is found that the honeycomb structure with pure water as lyophilized solvent is obtained and the pore size is about 110 μm, the thickness of pore wall increases with the increase of solid content. Using the tert-butyl alcohol to replace partial water as freeze-dried solvent, as the content of tert-butyl alcohol increases, the pore size decreases and then increases, and the pore size is the smallest near the eutectic point (20%) of water and tert-butanol. When the content of tert-butylalcohol is 50%, the PI chain flexibility is different, the resulting microstructure is also different. Further studying about the effect of chain flexibility and micromorphology on the compressive properties of aerogel, micromorphology of aerogel is found to be the main effect on its compressive ability.

    参考文献
    相似文献
    引证文献
引用本文

彭黎莹,王怡星,吉剑奇,刘梦云,秦家强,刘向阳.冷冻干燥制备聚酰亚胺气凝胶微观形态的调控[J].高分子材料科学与工程,2018,34(9):115-119. Liying Peng, Yixing Wang, Jianqi Ji, Mengyun Liu, Jiaqiang Qin, Xiangyang Liu. Control of Microstructure of Polyimide Aerogel Prepared by Freeze-Drying[J]. Polymer Materials Science & Engineering,2018,34(9):115-119.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2018-11-08
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司