热塑性聚氨酯/氯化聚乙烯发泡珠粒的制备及性能
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

国家自然科学基金资助项目(31270610);武汉市黄鹤英才计划(武人才办[2017]2号)


Preparation and Properties of Thermoplastic Polyurethane/Polyvinyl Chloride Foam Beads
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    以氯化聚乙烯(CPE)、热塑性聚氨酯(TPU)为原料,超临界CO2 为发泡剂,制备了TPU/CPE发泡珠粒。研究了TPU/CPE共混物的相容性、流变性能、发泡性能及CPE的含量对发泡珠粒抗收缩性能的影响。结果表明,CPE与TPU有良好的相容性,CPE的加入能有效改善TPU 的发泡性能与抗收缩性能,CPE含量为10%时,得到平均泡孔尺寸最小(8.851μm)、泡孔密度最大(1.763×1012cm-3)的发泡材料。TPU/CPE发泡珠粒的收缩率随着CPE含量的增加而降低,CPE的加入对降低TPU 发泡珠粒的收缩有着显著作用。

    Abstract:

    Thermoplastic polyurethane (TPU) foams that were modified with polyvinyl chloride (CPE) were prepared through autoclave foaming process using CO2 as blowing agent. Thermal behavior, rheological and foaming properties of the samples were evaluated. The results indicate that the addition of CPE can improve the melt strength of TPU and improve its foaming properties. The foaming material of which the average cell size is the smallest (8.851 μm) and the cell density is the maximum (1.796×1012 cm-3) is obtained when the content of CPE is 10%. The shrinkage ratio decreases with the increasing CPE content. The addition of CPE has a significant effect on reducing the shrinkage of TPU foam beads.

    参考文献
    相似文献
    引证文献
引用本文

黄 轲,张 荣,刘 颖,刘清亭,胡圣飞.热塑性聚氨酯/氯化聚乙烯发泡珠粒的制备及性能[J].高分子材料科学与工程,2018,34(9):126-131. Ke Huang, Rong Zhang, Ying Liu, Qingting Liu, Shengfei Hu. Preparation and Properties of Thermoplastic Polyurethane/Polyvinyl Chloride Foam Beads[J]. Polymer Materials Science & Engineering,2018,34(9):126-131.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2018-11-08
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司