全同聚丁烯-1注塑成型参数对力学性能和结晶形态的影响
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

泰山学者工程专项经费资助;国家自然科学基金资助项目(21174074);山东省重点研发计划(2015GGX102019);山东省自然科学基金资助项目(ZR2013BM004);山东省自然科学杰出青年基金资助项目(JQ201213);黄河三角洲学者工程专项经费资助(中国石油大学国家大学科技园管委会办公室);中国科学院工程塑料重点实验室(化学研究所)开放课题


Effect of Processing Conditions on Mechanical Properties and Crystalline Morphology of Isotactic Poly(butane-1) during Injection Molding
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    全同立构聚丁烯-1(iPB)根据加工条件的不同,在冷却结晶时会形成复杂的多晶结构和形貌。在注射成型加工过程中,iPB的结晶过程是在高的注射压力下进行的非等温流动诱导结晶。文中研究了注射成型的模具温度、注射压力及保压压力对iPB力学性能的影响,并通过差示扫描量热测试和偏振光学显微镜观察iPB的结晶行为。结果表明,低的模具温度可以提高制品的初始密度和室温放置4d后的成型密度,30~40 ℃时制品最终密度和体积收缩率最低。成型温度提高有利于改善制品的弯曲性能,但冲击强度显著降低。随着模具温度升高,制品的结晶度和熔点升高。注射成型中的流动诱导结晶可以改变iPB的晶体形态,制品表面形成微晶组成的取向层,内部较大的球晶显示出随注射流动方向取向的椭球形。

    Abstract:

    Due to the complex polymorphic behavior, isotactic poly(butene-1) (iPB) can crystallize into these crystalline modifications depending on preparation conditions. During the injection molding processing, iPB offers a flow-induced crystallization and subsequent heterothermal crystallization under high molding pressure. The influence of molding temperature, injection pressure and holding pressure on the mechanical properties of iPB was investigated. And then, the crystallization behaviors were observed by the differential scanning calorimetry(DSC) and polarized optical microscopy(POM). The results show that the low molding temperature can improve the initial density and formation density after 4 d. The final density and volumetric shrinkage are the lowest while the molding temperature is range of 30~40 ℃. The higher molding temperature can improve the flexural property but impact strength decreases dramatically. The flow-induces crystallization can affect the iPB spherulitic crystal morphology. The surface of the sample is an orientation layer composed of microcrystals and the inner layer contains bigger spherulites with the array according to the injection direction.

    参考文献
    相似文献
    引证文献
引用本文

张跃发,孙照博,邵华锋.全同聚丁烯-1注塑成型参数对力学性能和结晶形态的影响[J].高分子材料科学与工程,2018,34(10):105-109. Yuefa Zhang, Zhaobo Sun, Huafeng Shao. Effect of Processing Conditions on Mechanical Properties and Crystalline Morphology of Isotactic Poly(butane-1) during Injection Molding[J]. Polymer Materials Science & Engineering,2018,34(10):105-109.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2018-11-08
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司