(PS-g-LLDPE)-g-MAH 增容PA6/LLDPE/PS三元共混物的微观结构及力学性能
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:


Morphologies and Mechanical Properties of PA6/PS/LLDPE Ternary Blends Compatibilized by (PS-g-LLDPE)-g-MAH
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    以(聚苯乙烯(PS)-g-线型低密度聚乙烯(LLDPE))-g-马来酸酐(MAH)为相容剂,改变混合方法,制备了具有不同微观结构的尼龙6(PA6)/LLDPE/PS(60/20/20,质量分数)三元共混物。根据热力学、动力学因素,预判了共混物的微观结构;再结合扫描电镜和力学性能测试,考察了微观结构对力学性能的影响。结果表明,简单共混时,因界面张力的作用,在PA6中PS会包裹LLDPE形成壳核结构;该增容剂黏度大,增容时合适的混合方法,使其更易扩散至相界面,有利于阻碍PS包裹LLDPE,使两相独立分散;预判结果与测试结果相一致;壳核结构的出现,会掩盖LLDPE(核)的韧性,使材料呈现出硬而脆的特点;两相独立分散,在保证材料刚性的同时又能提高韧性;采用(PS-g-LLDPE)-g-MAH 先与PS、LLDPE混合再与PA6混合的共混法时,增容效果最好,其缺口冲击强度相较于简单共混物提高了近5倍,材料整体表现出硬而韧的特点。

    Abstract:

    PA6/PS/LLDPE(60/20/20,mass ratio) ternary blends compatibilized by (PS-g-LLDPE)-g-MAH with different morphologies were prepared by different processing method. The morphologies of the ternary blends were predicted according to thermodynamic and kinetic factors and verified by SEM tests, then the relationship between morphologies and mechanical properties was investigated by SEM and mechanical properties tests. The results reveal that the uncompatibilized blend presents a core-shell morphology with LLDPE encapsulated with PS in the PA6 matrix because of the role of interfacial tension. Due to the high viscosity of the compatibilizer, appropriate processing method should be advanced to make the compatibilizer diffuse to interface more easily during compatibilizing, then it would be beneficial to hinder PS form encapsulating LLDPE, the core-shell morphology could change to the morphology with two phase dispersed individually in PA6. Predicted morphologies show a consummate consistency with the results of SEM test. The toughness of LLDPE could be completely concealed and the materials have a hard and fragile tensile behavior with the core-shell morphology. The toughness of the ternary blends with constant rigidity could be improved when LLDPE and PS are dispersed individually. The best compatibilization efficiency could be achieved when the ternary blends are processed with mixed (PS-g-LLDPE)-g-MAH, LLDPE,PS firstly then mixed with PA6. In this case, the ternary blends have a 5 times higher notch impact strength than the simple blends and present a hard and toughness tensile behavior.

    参考文献
    相似文献
    引证文献
引用本文

沈 帆,董银春,黄昱峥,徐建平.(PS-g-LLDPE)-g-MAH 增容PA6/LLDPE/PS三元共混物的微观结构及力学性能[J].高分子材料科学与工程,2018,34(12):83-89. Fan Shen, Yinchun Dong, Yuzheng Huang, Jianping Xu. Morphologies and Mechanical Properties of PA6/PS/LLDPE Ternary Blends Compatibilized by (PS-g-LLDPE)-g-MAH[J]. Polymer Materials Science & Engineering,2018,34(12):83-89.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2019-01-07
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司