氨基硅氧烷改性水性聚氨酯自消光树脂的制备及性能
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

安徽省2017年度科技攻关项目(1704a0902018);安徽省高校自然科学研究重点项目 (KJ2016A792)


Preparation and Properties of Waterborne Polyurethane Self-Matting Resin Modified with Amino Siloxane
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    以聚醚N220、异氟尔酮二异氰酸酯、二羟甲基丙酸和1,4-丁二醇为单体,合成出水性聚氨酯预聚体;经中和乳化后,加入γ-氨丙基三乙氧基硅烷(APTES),制备出氨基硅氧烷改性水性聚氨酯自消光树脂。通过红外光谱、扫描电镜、光泽、热分析等对胶膜进行表征,并探讨APTES含量对胶膜光泽度、耐水性、力学性能和热性能的影响。结果表明,胶膜表面微观粗糙,达到消光要求;当APTES添加量占乳液的质量分数为0.4%时,胶膜60°光泽度为3.2,吸水率为10.52%,水接触角为80°,拉伸强度为14.32 MPa,断裂伸长率为201%,热失重10%时的分解温度较未改性的聚氨酯膜提高了13 ℃。

    Abstract:

    Using polyether N220, isophorone diisocyanate, dimethylol propionic acid and 1, 4-butanediol as monomers to prepare waterborne polyurethane prepolymer, after it was neutralized and emulsified, γ-aminopropyltriethoxysilane(APTES) was added, and then the waterborne polyurethane self-matting resin was modified with amino siloxane. The infrared spectrometer, SEM, gloss meter, thermal analyzer and so on were used to characterize the films, and the effects of content of APTES on the glossiness, water resistance, acid and alkali resistance, mechanical property and thermal performance of tatex films were investigated. The results show that the film surface is rough enough to satisfy extinction requirements. When the mass fraction of APTES is 0.4%, the 60° gloss of the film is 3.2, the water absorption rate is 10.52%, the water contact angle is 80°, the tensile strength is 14.32 MPa, the elongation at break is 201%, the thermal decomposition temperature at 10% mass loss rate, compared with the unmodified polyurethane film, is increased by 13 ℃.

    参考文献
    相似文献
    引证文献
引用本文

丁 琳,杨建军,吴庆云,吴明元,张建安.氨基硅氧烷改性水性聚氨酯自消光树脂的制备及性能[J].高分子材料科学与工程,2019,35(1):19-24. Lin Ding, Jianjun Yang, Qingyun Wu, Mingyuan Wu, Jian’an Zhang. Preparation and Properties of Waterborne Polyurethane Self-Matting Resin Modified with Amino Siloxane[J]. Polymer Materials Science & Engineering,2019,35(1):19-24.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2019-02-13
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司