超临界二氧化碳发泡聚乙烯醇/贝壳粉复合泡沫的泡孔结构调控
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

国家自然科学基金国际(地区)合作交流项目(51720105012)


Cell Structure Controlling of Polyvinyl Alcohol/Shell Powder Composite Foam Prepared by Supercritical Carbon Dioxide Foaming Technology
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    以水为增塑剂兼物理发泡剂,结合超临界二氧化碳发泡技术制备了聚乙烯醇(PVA)/贝壳粉复合泡沫,研究了多种因素对泡孔结构的影响。结果表明,贝壳粉作为异相成核剂,能增加成核点数,提高熔体强度,更好地支撑泡孔形成与生长;提高饱和压力和适度交联能增大二氧化碳在PVA基体中的溶解度,增多泡孔数目,减小尺寸,分布更均匀;发泡温度升高,二氧化碳扩散速度增加,孔径分布变宽。当贝壳粉含量10%、饱和压力15 MPa、发泡温度80 ℃、交联剂含量0.5%时,获得的复合泡沫结构最优,对Cu(II)、Pb(II)及Cd(II)均有较好的吸附性。

    Abstract:

    Polyvinyl alcohol (PVA)/shell powder composite foams were prepared by using water as both plasticizer and physical blowing agent combining with supercritical carbon dioxide technology. The results show that shell powders, as heterogeneous nucleating agent, could increase the nucleation point and melt strength of the system, thus better supporting the formation and growth of cells; proper cross-linking increases the solubility of carbon dioxide in the PVA matrix, leading to the decrease of the cell size and increase of the cell number and distribution uniformity. Rising the foaming temperature, the diffusion of carbon dioxide is accelerated, resulting in a more uneven growth rate and distribution of cells. With 10% shell powders and 0.5% crosslinking agent, and at 15 MPa saturation pressure and 80 ℃ foaming temperature, the cell structure of the composite foam is the best, and the foam has good adsorption ability on Cu (II), Pb (II) and Cd (II).

    参考文献
    相似文献
    引证文献
引用本文

谢页平,邱文婷,李 莉.超临界二氧化碳发泡聚乙烯醇/贝壳粉复合泡沫的泡孔结构调控[J].高分子材料科学与工程,2019,35(3):124-130. Yeping Xie, Wenting Qiu, Li Li. Cell Structure Controlling of Polyvinyl Alcohol/Shell Powder Composite Foam Prepared by Supercritical Carbon Dioxide Foaming Technology[J]. Polymer Materials Science & Engineering,2019,35(3):124-130.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2019-04-09
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司