扩链聚乳酸的超临界CO2 发泡与结晶
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

国家自然科学基金委员会与中国工程物理研究院联合基金资助项目(U1530144)


Supercritical CO2 Foaming and Crystallization of Chain Extended Polylactic Acid
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    采用超临界CO2釜式发泡,通过快速降压对扩链聚乳酸进行发泡。采用差示扫描量热仪、广角X射线衍射分析仪、扫描电子显微镜及图像分析系统研究了饱和压力与饱和时间对扩链聚乳酸发泡及结晶行为的影响。研究结果表明,经过超临界CO2釜式发泡,扩链聚乳酸由无定形态转变为半结晶态。扩链聚乳酸在115 ℃、18 MPa下,采用超临界CO2饱和2 h后快速卸压发泡,制得的聚乳酸泡沫的发泡倍率为28倍,泡孔平均孔径为57 μm,结晶度为32.8%,泡孔为均匀的闭孔结构。

    Abstract:

    The chain extended polylactic acid (E-PLA) was foamed with supercritical CO2 in autoclave through rapid depressurizing. The effects of saturation pressure and time on the foaming and crystallization behavior of E-PLA were investigated by differential scanning calorimeter, wide angle X-ray diffraction analyzer, scanning electron microscope and image analysis system. The experimental results show that after autoclave foaming, the E-PLA is transferred from amorphous to semi-crystalline state. After saturated with supercritical CO2 at 115 ℃ and 18 MPa for 2 h, the E-PLA is rapidly depressurized; the obtained E-PLA foam has the expansion ratio of 28, The average cell size of 57 μm and the crystallinity of 32.8%.

    参考文献
    相似文献
    引证文献
引用本文

余 智,吴东森,邹华维,刘鹏波.扩链聚乳酸的超临界CO2 发泡与结晶[J].高分子材料科学与工程,2019,35(3):131-135. Zhi Yu, Dongsen Wu, Huawei Zou, Pengbo Liu. Supercritical CO2 Foaming and Crystallization of Chain Extended Polylactic Acid[J]. Polymer Materials Science & Engineering,2019,35(3):131-135.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2019-04-09
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司