溢流法水驱动弹头辅助注塑管件残余壁厚的形成与工艺参数影响
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

国家自然科学基金资助项目(51563010,21664002);江西省自然科学基金资助项目(20181BAB206014)


Formation Mechanism of Residual Wall Thickness of Overflow Water- Projectile-Assisted Injection Molding Pipe and the Effects of Processing Parameters
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    溢流法水驱动弹头辅助注塑(W-PAIM-O)工艺可制得残余壁厚(RWT)更薄更均匀的管件。采用模拟手段分析了W-PAIM-O工艺中RWT的形成机理,采用单因素实验法考察了熔体温度、熔体注射压力、注水延迟时间、注水压力和模具温度5个工艺参数对RWT的影响。模拟发现,RWT不仅主要取决于弹头的截面尺寸,还与弹头穿透时对侧面熔体的拖曳作用有关;在考察的几个工艺参数中,熔体温度越高,RWT越小,但熔体温度过高时RWT反而增大;熔体注射压力越大RWT越小,但熔体注射压力过大反而使RWT增大;随着模具温度的升高,RWT变薄,模具温度超过一定值后,RWT趋于稳定;RWT随注水延迟时间的延长而变厚;注水压力对W-PAIM-O管件RWT影响较小。

    Abstract:

    Overflow water- projectile-assisted injection molding (W-PAIM-O) technology can be used to manufacture pipes with more thinner and more even residual wall thickness (RWT). Numerical simulation was performed to analysis the formation mechanism of the RWT of W-PAIM-O pipe. Single factor experiments were carried out to study the effects of processing parameters such as melt temperature, melt injection pressure, water injection delay time, water pressure, and mold temperature on RWT of W-PAIM-O pipe. It is found from the simulation results that the RWT of the pipe is not only determined by the cross-section of the projectile,but also by the effect of the towing area which is located at the side of projectile. The influences of the five processing parameters on the RWT of W-PAIM-O pipe were discovered from the experimental results. The RWT decreases with increasing the melt temperature while increases with a too high melt temperature. The higher the melt injection pressure is, the smaller the RWT is, but the RWT increases when the melt injection pressure is too high. With the increase of mold temperature, the RWT becomes thinner and the RWT tends to be stable after the mold temperature exceeds a certain value. The RWT increases with increasing the water injection delay time. Water pressure has little influence on the RWT of W-PAIM-O pipe.

    参考文献
    相似文献
    引证文献
引用本文

匡唐清,潘俊宇,刘文文,柳和生.溢流法水驱动弹头辅助注塑管件残余壁厚的形成与工艺参数影响[J].高分子材料科学与工程,2019,35(4):108-114. Tangqing Kuang, Junyu Pan, Wenwen Liu, Hesheng Liu. Formation Mechanism of Residual Wall Thickness of Overflow Water- Projectile-Assisted Injection Molding Pipe and the Effects of Processing Parameters[J]. Polymer Materials Science & Engineering,2019,35(4):108-114.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2019-05-10
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司