聚酰胺聚醚弹性体/石墨烯纳米复合材料的制备与表征
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

国家自然科学基金资助项目(51503088);江苏省自然科学基金资助项目(BK20140513);中国博士后科学基金(2016M591796)


Preparation and Characterization of Polyamide Polyether Elastomer/Graphene Nanocomposites
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    采用一步法原位聚合制备了聚酰胺聚醚弹性体/石墨烯(PA6-b-PEG/GNs)纳米复合材料。傅里叶变换红外光谱测试结果表明,加入一定量的GNs能够促进PA6-b-PEG缩聚反应;X射线衍射和差示扫描量热分析显示,GNs的加入能提高纳米复合材料的结晶度和熔点,当GNs含量为5%时,纳米复合材料的结晶温度和熔点均达到最大值;热重分析表明,随着GNs含量的增加,复合材料的起始分解温度、分解终止温度及热稳定性均得到有效提高;拉伸测试结果表明,PA6-b-PEG/GNs纳米复合材料的拉伸强度和弹性模量均比PA6-b-PEG高,但其断裂伸长率下降;此外,扫描电镜结果显示,GNs的加入能够降低PA6-b-PEG的微相分离程度,改善材料的相容性。

    Abstract:

    In this study, polyamide polyether elastomer/graphene (PA6-b-PEG/GNs) nanocomposites were prepared by in situ polymerization via one-step method. FT-IR characterization shows that the polycondensation of PA6-b-PEG could be promoted by the addition of GNs. X-ray diffraction and DSC analyzation exhibit that the crystallinity and melting temperature of PA6-b-PEG/GNs nanocomposites are higher than those of PA6-b-PEG. When the GNs content is 5%, the crystallization temperature and melting point of nanocomposites reach the maximum values. The results of TGA display that the initial decomposition temperature, decomposition termination temperature, thermal stability of the composites are effectively improved by GNs. The tensile test results show that PA6-b-PEG/GNs nanocomposites have the higher tensile strength and elastic modulus than PA6-b-PEG, but their elongation at break decreases. In addition, SEM show that GNs can improve the rigidity of PA6-b-PEG, reduce its microphase separation, and improve its material compatibility.

    参考文献
    相似文献
    引证文献
引用本文

闫东广,宋玮琦,李姜红,王春亭.聚酰胺聚醚弹性体/石墨烯纳米复合材料的制备与表征[J].高分子材料科学与工程,2019,35(4):161-165. Dongguang Yan, Weiqi Song, Jianghong Li, Chunting Wang. Preparation and Characterization of Polyamide Polyether Elastomer/Graphene Nanocomposites[J]. Polymer Materials Science & Engineering,2019,35(4):161-165.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2019-05-10
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司