熔融沉积成型参数对改性聚乳酸冲击性能的影响
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

国家重点研发计划项目(2016YFB0302300);福建师范大学泉港石化研究院专项资金(2016YJY20)


Influence of Fused Deposition Modeling Processing Parameters on Impact Properties of Modified Poly(lactic acid)
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    以聚乳酸(PLA)为基体、热塑性聚氨酯(TPU)和甲基丙烯酸甲酯-有机硅-苯乙烯共聚物(S-2001)为增韧剂,通过熔融共混法制备了改性PLA3D打印线材,采用正交试验探索了底板温度、打印温度、沉积方式、打印层厚和打印速度等熔融沉积成型(FDM)参数对改性PLA冲击性能的影响。结果表明,当底板温度为90 ℃,喷嘴温度为190 ℃,沉积方式为45°/45°,打印层厚为0.4mm 和打印速度为45mm/s时,FDM 试样的冲击强度达到最大值,而且打印层厚和沉积方式对改性PLAFDM 试样的冲击性能影响显著;扫描电镜分析表明增加打印层厚有利于材料吸收冲击功,奇数层与偶数层之间的不同沉积角度对试样冲击强度的提高影响不一,45°/45°为宜;同时,最优工艺的FDM 试样的冲击强度比注塑试样低,为注塑试样的71.4%。

    Abstract:

    The modified poly(lactic acid)(PLA) filaments were prepared by melt mixing. The influence of fused deposition modeling (FDM) processing parameters on the impact properties of modified PLA were investigated by orthogonal test, including bed temperature, nozzle temperature, deposition style, layer thickness and printing speed. The results indicate that the impact strength of FDM specimen is the greatest with the processing parameters as follows: bed temperature of 90 ℃, nozzle temperature of 190 ℃, deposition style of 45°/45°, layer thickness of 0.4 mm and printing speed of 45 mm/s. Furthermore, the layer thickness and the deposition style have a significant effect on the impact properties of modified PLA FDM specimen. The SEM images show that increasing layer thickness is favor of absorbing energy when the materials were impacted. Different deposition angles between odd and even number layers have different effects on the increase of impact strength, and 45°/45°is appropriate. Meanwhile, compared with injection molding, the impact strength of FDM specimen is lower, just 71.4% as high as that of injection molding specimen.

    参考文献
    相似文献
    引证文献
引用本文

夏新曙,林鸿裕,杨松伟,黄宝铨,钱庆荣,陈庆华,肖荔人.熔融沉积成型参数对改性聚乳酸冲击性能的影响[J].高分子材料科学与工程,2019,35(5):88-93. Xinshu Xia, Hongyu Lin, Songwei Yang, Baoquan Huang, Qingrong Qian, Qinghua Chen, Liren Xiao. Influence of Fused Deposition Modeling Processing Parameters on Impact Properties of Modified Poly(lactic acid)[J]. Polymer Materials Science & Engineering,2019,35(5):88-93.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2019-07-11
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司