芯片补强固定光热双固化封装材料的制备与表征
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

陕西省重点研发计划项目(2018GY-115);陕西省留学人员科技活动择优项目(2017030)


Preparation and Characterization of Chip-Reinforced and Fixed Light-Heat Dual-Cure Packaging Materials
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    以双酚A型环氧树脂828el和改性脂环族环氧树脂2021P复配作为树脂体系,Irgacure261为阳离子光引发剂,三氟化硼单乙胺为热固化剂,活性硅微粉为填料,白炭黑为增稠剂混合配制成胶液,制备用于芯片补强固定的高性能光热双固化封装材料。通过紫外光能量和差示扫描量热测试表征确定胶黏剂固化工艺,并研究了填料种类和用量对双固化封装材料剪切强度、黏度、热膨胀系数(CTE)、吸湿率和热稳定性能的影响。结果表明,当改性脂环族环氧树脂2021P、双酚A型环氧树脂828el、Irgacure261、三氟化硼单乙胺和活性硅微粉质量比为90∶10∶3∶2.5∶40,光固化条件为UV能量2800 mJ/cm2,热固化条件为80 ℃/30 min时,可得到满足黏接强度为25.2 MPa,CTE为130×10-6 ℃-1(55~70 ℃)、240×10-6 ℃-1(115~130 ℃),吸湿率为0.131%,热稳定性好的光热双固化封装材料。

    Abstract:

    The bisphenol A epoxy resin 828el and modified alicyclic epoxy resin 2021P compound as resin system, Irgacure261 as carnation photoinitiator, boron trifluoride monoethylamine as heat curing agent, activated silicon fine powder as filler,and white carbon as thickener were mixed to prepare the glue solution. And high-performance light-heat dual-cure packaging materials for chip-reinforced and fixed were prepared with the glue solution. The adhesive curing process was determined by UV energy meter and differential scanning calorimetry (DSC), and the effects of the type and amount of filler on the shear strength, viscosity, thermal expansion coefficient(CTE), moisture absorption rate and thermal stability of the dual-cured packaging materials were investigated. The results show that when the mass ratio of modified aliphatic epoxy resin 2021P, bisphenol A epoxy resin 828el, Irgacure261, boron trifluoride monoethylamine and active silica powder is 90∶10∶3∶2.5∶40, the curing process system is as follows∶ UV energy of 2800 mJ/cm2 to achieve dry, 80 ℃/30 min for complete curing, light-heat double-cured packaging materials with good thermal stability are got, the adhesive strength of 25.2 MPa, the CTE of 130×10-6 ℃-1 (55~70 ℃) and 240×10-6 ℃-1 (115~130 ℃), the moisture absorption rate of 0.131%.

    参考文献
    相似文献
    引证文献
引用本文

李会录, 王 刚, 霍 翠, 刘卫清, 李 涛.芯片补强固定光热双固化封装材料的制备与表征[J].高分子材料科学与工程,2019,35(6):105-110. Huilu Li, Gang Wang, Cui Huo, Weiqing Liu, Tao li. Preparation and Characterization of Chip-Reinforced and Fixed Light-Heat Dual-Cure Packaging Materials[J]. Polymer Materials Science & Engineering,2019,35(6):105-110.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2019-07-22
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司