聚氨酯弹性体的选择性激光烧结
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

科技部国家重点研发计划政府间国际科技创新合作重点专项(2017YFE0111500);欧洲地平线2020玛丽居里项目(734164)


Selective Laser Sintering of Polyurethane Elastomers
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    研究了聚氨酯弹性体(TPU)粉末的选择性激光烧结(SLS)行为。研究了TPU 烧结过程中粉床温度及激光能量密度对首层烧结区域翘曲行为的影响,确定TPU 的烧结窗口为(Tc-Tg2);研究了粉体粒径及纳米二氧化硅含量对TPU 烧结的影响,结果表明粒径在100μm 左右的一个较宽范围内都可以正常打印,且打印制件能维持较好的精度和力学性能;随着纳米二氧化硅含量的增加,TPU 粉体流动性逐渐变好,但烧结制件的力学性能呈现先升高后下降的趋势,当纳米二氧化硅质量分数为0.2%时,TPU 烧结制件拉伸强度可达到28.8 MPa,断裂伸长率为615%,此时TPU 烧结性能最优异。

    Abstract:

    The selective laser sintering (SLS) behavior of polyurethane elastomer (TPU) powder was studied in this paper. The effect of powder bed temperature and laser energy density on the warpage behavior of the first layer sintering zone during the sintering process of TPU was studied, and the sintering window of TPU was determined to be (Tc-Tg2); the effect of powder particle size and nano-silica content on the properties of laser-sintered TPU was studied. The results show that when the particle size is in a wide range of about 100 μm, the printed parts can maintain good precision and mechanical properties; with the increase of nano-silica content, the flowability of TPU powder gradually becomes better, but the mechanical properties of TPU sintered parts increase first and then decrease. When the mass fraction of nano-silica is 0.2%, the tensile strength of TPU sintered parts can reach 28.85 MPa and the elongation at break is 615%, and the TPU has the best sintering performance.

    参考文献
    相似文献
    引证文献
引用本文

甘鑫鹏,王金志,费国霞,夏和生.聚氨酯弹性体的选择性激光烧结[J].高分子材料科学与工程,2019,35(8):87-93. Xinpeng Gan, Jinzhi Wang, Guoxia Fei, Hesheng Xia. Selective Laser Sintering of Polyurethane Elastomers[J]. Polymer Materials Science & Engineering,2019,35(8):87-93.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2019-09-16
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司