短玻纤增强聚丙烯水辅助注射成型纤维取向数值模拟
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

国家自然科学基金资助项目(21664002,51563010,51403615);江西省教育厅科技项目(GJJ161049);江西省研究生创新专项(YC2017-S058)


Numerical Simulation of Fiber Orientation in Water-Assisted Injection Molding of Short Glass Fiber Reinforced Polypropylene
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    基于Folgar-Tucker纤维取向模型,利用Moldex3D对三维长直管件进行溢流法水辅助注射成型可视化研究。结果表明,在制品初始段位置的水道层区域纤维取向倾向于无序状态,而在制品的中间段及末尾段位置的纤维倾向于沿流动方向形成取向;通过适当的增加注水延迟时间可以有效地改善制品初始段位置的纤维沿流动方向的取向。另外,还发现沿流动方向的纤维取向最有序的位置是靠近壳层位置的芯层区域;在制品的末端位置,注水压力、熔体温度显著影响纤维沿流动方向的取向。

    Abstract:

    Based on the Folgar-Tucker fiber orientation model, the visualization of water-assisted injection molding three-dimensional long straight pipe was carried out by using Moldex3D. It is found that the fibers in the water channel layer near water inlet tend to be disordered, whereas at the position near the middle and end of water channel, fibers tend to orienting along flow direction; by appropriately increasing the water injection delay time can result in more fibers at the initial direction of the product orienting along the flow direction. In addition, it has also been found that the glass fibers are orientated remarkably in the core layer and slightly in the region near the mold wall. At the end position of the product, the water injection pressure and melt temperature can significantly affects the orientation of the fibers along the flow direction.

    参考文献
    相似文献
    引证文献
引用本文

张 伟,柳和生,黄兴元,余 忠,章 凯,陈忠仕.短玻纤增强聚丙烯水辅助注射成型纤维取向数值模拟[J].高分子材料科学与工程,2019,35(8):105-111. Wei Zhang, Hesheng Liu, Xingyuan Huang, Zhong Yu, Kai Zhang, Zhongshi Chen. Numerical Simulation of Fiber Orientation in Water-Assisted Injection Molding of Short Glass Fiber Reinforced Polypropylene[J]. Polymer Materials Science & Engineering,2019,35(8):105-111.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2019-09-16
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司