注气工艺对外部气体辅助注塑成型制品翘曲与凹痕的影响
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

江西省高等学校科技落地计划(KJLD13087);江西省研究生创新专项资金(YC2013-B013)


Influence of Gas-Injection Processing Conditions on Warpage and Sink Mark of Part by External Gas-Assisted Injection Molding
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    注塑制品翘曲变形与凹痕是2种严重缺陷,文中基于带加强筋平板制品实验研究了外部气体辅助注塑成型(EGAIM)中注气工艺参数对制品翘曲与凹痕的影响规律及原因。通过采用单因素方差分析阐明了气体注射延迟时间、气体保压压力及气体保压时间对制品的翘曲与凹痕都有显著影响,其中气体注射延迟时间的影响最显著。制品翘曲与凹痕随注气工艺参数变化呈现不同特征:随着注射延迟时间的延长,制品翘曲与凹痕呈相反的变化趋势,制品翘曲变形减小而凹痕深度增加;提高气体保压压力,制品凹痕深度单调减小而翘曲呈“U”形曲线变化;增长保压时间,制品翘曲与凹痕都有减小的趋势。这些影响规律的总结为减小EGAIM 制品的翘曲与凹痕提供了依据。

    Abstract:

    The warpage and sink mark of injection molded parts are two kinds of serious defects. The effect of the gas-injection processing parameters of external gas-assisted injection molding(EGAIM) on the warpage and sink mark was investigated by the experiment of flat part with ribs. Through the single factor analysis of variance, it is shown that the gas delay time, gas holding pressure and gas holding time have significant influence on warpage and sink mark of part, and the gas delay time is the most significant effect on warpage and sink mark. With changing processing conditions, the variations of warpage and sink mark of part were summarized as follows: contrary effects, warpage decreases but sink mark increases with increasing gas delay time; sink mark is monotonously reduced and warpage varies as U shape curve with increasing gas holding pressure; both warpage and sink mark have a decreasing trend with increasing gas holding time. These results could be used to help minimize warpage and sink mark of EGAIM parts.

    参考文献
    相似文献
    引证文献
引用本文

肖清武,柳和生,黄益宾,余 忠,黄东有.注气工艺对外部气体辅助注塑成型制品翘曲与凹痕的影响[J].高分子材料科学与工程,2019,35(8):112-117. Qingwu Xiao, Hesheng Liu, Yibin Huang, Zhong Yu, Dongyou Huang. Influence of Gas-Injection Processing Conditions on Warpage and Sink Mark of Part by External Gas-Assisted Injection Molding[J]. Polymer Materials Science & Engineering,2019,35(8):112-117.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2019-09-16
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司