注射成型后期热处理对聚碳酸酯性能的影响
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:


Effect of Heat Treatment After Injection Molding on the Properties of Polycarbonate
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    考察了退火方式和退火工艺对聚碳酸酯(PC)残余应力和拉伸性能的影响。光弹法定量分析结果表明,退火能够显著降低PC的残余应力,残余应力随退火温度升高和退火时间延长而减小。但退火温度越高,退火温度和退火时间对PC残余应力影响差异性逐渐减弱。拉伸测试结果表明,130℃4h退火工艺下,开模取件后立即退火使PC拉伸强度提高5.5%,而完全冷却后退火则使PC拉伸强度降低8.7%。综合分析表明,退火消除的流动残余应力将降低PC的拉伸强度,而退火消除的热残余应力则会提高PC的拉伸强度,退火过程中拉伸强度的变化,是流动残余应力和热残余应力偶合作用变化的结果。

    Abstract:

    The influences of annealing methods and annealing parameters on the residual stress and tensile properties of polycarbonate(PC) were investigated. The quantitative analysis results by the photoelastic test show that the annealing can significantly reduce the residual stress of PC, and the residual stress decreases with the increase of annealing temperature and annealing time. While higher the annealing temperature is, lower the influence difference on the residual stress of PC is with the variation of the annealing temperature and annealing time. In addition, the results of the tensile test indicate that when the annealing temperature is 130 ℃ and the annealing time is 4 h, the tensile strength is increased by 5.5% by the first annealing method, which is that annealing occurs immediately after PC removed from the injection mould. However, the tensile strength is decreases by 8.7% by the second annealing method, which is that annealing occurs after PC cooled completely. Besides, the comprehensive analysis shows the change of the tensile strength during annealing is the result of the coupling effect of flow residual stress and thermal residual stress. Because that decrease of the flow residual stress decreases the tensile strength, but decrease of the thermal residual stress increases the tensile strength.

    参考文献
    相似文献
    引证文献
引用本文

葛 勇,相 宁,王博伦,王 韬,颜 悦.注射成型后期热处理对聚碳酸酯性能的影响[J].高分子材料科学与工程,2019,35(9):89-94. Yong Ge, Ning Xiang, Bolun Wang, Tao Wang, Yue Yan. Effect of Heat Treatment After Injection Molding on the Properties of Polycarbonate[J]. Polymer Materials Science & Engineering,2019,35(9):89-94.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2019-12-03
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司