单模具多规格聚乳酸微管挤出成型工艺
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

国家自然科学基金资助项目(51675079,11502044);中央高校基本业务费(DUT17RC(3)104)


Extrusion Process of Multi-Specification Polylactide Micro Tubes by a Single Extrusion Die
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    系统研究了聚乳酸微管的挤出成型工艺,获得了注气量、螺杆转速、牵引速度对微管外径、壁厚和椭圆度的影响规律。实验结果表明,注气量、螺杆转速、牵引速度对微管外径和壁厚的影响显著,且呈非线性变化。其中,牵引速度和螺杆转速相对于注气量对微管外径的影响程度较大;螺杆转速、牵引速度和注气量对微管壁厚的影响程度依次减弱。注气量直接影响微管截面的椭圆度,注气量越大,椭圆度越小,在注气量较小时,注气量增大1倍,椭圆度可降低68%。通过改变牵引速度、螺杆转速、注气量及其组合,可以达到采用1套模具顺序挤出4种规格聚乳酸微管的目的。

    Abstract:

    In this paper, the extrusion process of polylactide micro tubes was studied systematically. The effects of gas flow rate, screw speed and pulling speed on outer diameter, wall thickness and ovality of the micro tubes were obtained. Experimental results show that gas flow rate, screw speed and pulling speed have significant nonlinear effects on outer diameter and wall thickness. Pulling speed and screw speed affect the outer diameter of the micro tubes more obviously than gas flow rate. Screw speed, pulling speed and gas flow rate have successively weak effects on the thickness of the micro tubes. The ovality of the micro-tubes is directly affected by the gas flow rate, and the ovality decreases obviously with the increase of the gas flow rate. At lower gas flow rates, the ovality can be reduced by 68% if the gas injection volume is doubled. By changing pulling speed, screw speed, gas flow rate and the combination of these parameters, four specifications of micro tubes can be extruded in sequence by a single extrusion die.

    参考文献
    相似文献
    引证文献
引用本文

魏云波,王敏杰,赵丹阳,刘 奎,申振楠.单模具多规格聚乳酸微管挤出成型工艺[J].高分子材料科学与工程,2019,35(9):95-102. Yunbo Wei, Minjie Wang, Danyang Zhao, Kui Liu, Zhennan Shen. Extrusion Process of Multi-Specification Polylactide Micro Tubes by a Single Extrusion Die[J]. Polymer Materials Science & Engineering,2019,35(9):95-102.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2019-12-03
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司