马来酸酐改性木质素对聚乳酸/环氧大豆油性能的影响
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:


Effects of Maleic Anhydride Modified Lignin on Fully Biobased Poly(lactic acid)/Epoxidized Soybean Oil Composites
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    制备了一种基于马来酸酐改性木质素(LM)、环氧大豆油(ESO)与聚乳酸(PLA)的全生物基复合材料(PLA/ESO/LM)。采用傅里叶变换红外光谱、核磁共振氢谱对LM进行测试与分析,确认马来酸酐改性木质素的结构;以差示扫描量热仪、热重分析仪、偏光显微镜等研究复合材料的热学性能及内部结构。结果表明,与PLA相比,PLA/ESO/LM复合材料冷结晶温度降低,结晶行为增强,结晶度提高;同时PLA/ESO/LM复合材料的初始热分解温度比PLA提高了35 ℃,表现出更高的热稳定性。通过优化复合材料的比例得出PLA/20ESO/0.5LM的复合材料具有最优的综合性能,拉伸强度为55 MPa,断裂伸长率提升到198%,约为PLA的20倍,PLA材料的综合性能得到极大提高。

    Abstract:

    A fully biobased composite(PLA/ESO/LM) consisting of poly(lactic acid)(PLA), epoxidized soybean (ESO) and maleic anhydride modified lignin (LM) was fabricated in the present study. FT-IR and NMR were utilized to identify the structure of modified lignin. Thermal properties and thermal stabilization of the composite were characterized by conducting the DSC and TG experiments. The POM was used to observe the internal structure of the composite. Comparing with pure PLA, the PLA/ESO/LM composite shows a lower cold crystallization temperature, enhanced crystallization behavior and improved degree of crystallization. Besides, the results suggest that the start thermal decomposition temperature of PLA/ESO/LM is 35 ℃ higher than that of pure PLA, indicating a higher thermal stabilization. In addition, under an optimal condition of composition ratio, the composite of PLA/20ESO/0.5LM shows the best comprehensive performance with the tensile strength of 55 MPa and the elongation at break at 198%, which is 20-fold greater than that of pure PLA.

    参考文献
    相似文献
    引证文献
引用本文

梁孝林,刘文毅,章丰凯,杨雯迪,施冬健,陈明清.马来酸酐改性木质素对聚乳酸/环氧大豆油性能的影响[J].高分子材料科学与工程,2019,35(10):61-67. Xiaolin Liang, Wenyi Liu, Fengkai Zang, Wendi Yang, Dongjian Shi, Mingqing Chen. Effects of Maleic Anhydride Modified Lignin on Fully Biobased Poly(lactic acid)/Epoxidized Soybean Oil Composites[J]. Polymer Materials Science & Engineering,2019,35(10):61-67.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2019-12-03
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司