基于电场驱动熔融喷射3D打印大面积聚甲基丙烯酸甲酯微结构制造方法
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

国家自然科学基金资助项目(51775288,51875300);山东省重点研发计划(2018GGX103022)


Large-Area Polymethyl Methacrylate Microstructures Fabricated by Electric-Field-Driven Fused Jet Deposition 3D Printing
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    针对大面积聚甲基丙烯酸甲酯(PMMA)微结构低成本制造的难题以及高分辨率PMMA成型的实际需求,提出一种基于电场驱动熔融喷射沉积3D打印实现大面积PMMA微结构高效低成本制造的新方法。通过高速摄像机实验观测和系列打印实验研究,揭示了主要工艺参数对于成型过程、打印分辨率、打印质量的影响和规律,优化的工艺参数范围为:电压1200~1300 V,气压3~10 kPa,打印高度200~400 μm,打印速度5~20 mm/s,材料加热温度210~230 ℃。利用提出的新方法,结合优化出的工艺参数,采用内径250 μm的喷嘴,实现了最小特征尺寸15 μm、图形面积70 mm×70 mm大尺寸微模具以及高宽比达到9∶1大面积复杂微结构和组织工程支架的制造。

    Abstract:

    In order to implement the low cost fabrication of large-area polymethyl methacrylate (PMMA) microstructures and high resolution PMMA forming, this paper presented a novel method for fabricating large-area PMMA microstructures by using an electric-field-driven fused jet deposition 3D printing. Combining the experimental observation using high-speed CCD and a serial of printing experiments conducted, the effects and rules of the main process parameters (including voltage, air pressure, printing height, printing speed, heating temperature) on the forming process and printing resolution as well as printing quality were revealed. Using a nozzle with an inner diameter of 250 μm and the optimized process parameters, a large-size micro-scale mold with the minimum feature size of 15 μm and patterned area of 70 mm×70 mm, and large-area complex 3D microstructures with a high aspect ratio of 9∶1 and the tissue scaffold are achieved. The results indicate that the proposed method provides a feasible solution for producing large-area PMMA microstructures with low-cost and high throughput.

    参考文献
    相似文献
    引证文献
引用本文

杨 昆,杨建军,赵佳伟,彭子龙,韦子龙,兰红波.基于电场驱动熔融喷射3D打印大面积聚甲基丙烯酸甲酯微结构制造方法[J].高分子材料科学与工程,2019,35(10):115-123. Kun Yang, Jianjun Yang, Jiawei Zhao, Zilong Peng, Zilong Wei, Hongbo Lan. Large-Area Polymethyl Methacrylate Microstructures Fabricated by Electric-Field-Driven Fused Jet Deposition 3D Printing[J]. Polymer Materials Science & Engineering,2019,35(10):115-123.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2019-12-03
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司