注塑工艺参数和超声外场对聚丙烯制件结晶结构的影响
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

国家自然科学基金资助项目(51575080,51175060)


Influence of Injection Process Parameters and Ultrasonic Field on Crystalstructure of Polypropylene Parts
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    针对模腔内熔体温度对制件冷却过程中其内部分子的凝聚结构及结晶形态的影响,通过自行设计制造的带有热电偶传感器和超声外场的注塑成型实验系统,采用单因素实验方法,通过测量PP制件成型过程中模腔不同位置处的熔体温度同时利用X射线衍射法,对制件内部微观结构形态的检测分析,研究了不同工艺参数和超声功率变化,对制件内部分子凝聚态结构的影响。结果表明,模腔内熔体峰值温度的升高及降温时间的延长,有利于制件内部分子形成结晶结构;但过高的熔体温度则不利于结晶结构的形成。适当增大超声功率能够有效促进制件内部分子生成结晶结构,使其结晶度提高;但过高的超声功率会使制件的结晶度下降。试验工艺参数条件下,施加600 W超声功率时,制件获得平均48.06%的最高结晶度,有效地提高了制件的力学性能。

    Abstract:

    The influence of melt cooling process on the internal molecule condensed structure and crystallization behavior of the parts was studied by the self-designed and manufactured injection molding test system, which containing thermocouple sensor and ultrasonic vibrator. The melt temperature at different positions of mould cavity was measured during the molding process of PP parts by single factor experiments, and the microstructure morphology of parts was explored by XRD. The effects of different technological parameters and ultrasonic powers on the internal molecular condensed matter structure were studied. The results show that the increase of the peak temperature and cooling time are beneficial to the formation of the molecular crystal structure, but the crystallinity will decrease under an excessive temperature, and the crystallinity increases first and then decreases with the increase of the ultrasonic power. When the ultrasonic power is 600 W, the average crystallinity of the parts is the highest, which is 48.06%. It indicates that appropriate ultrasonic field can effectively promote the production of the crystal structure during the cooling process, thus improve the mechanical properties effectively.

    参考文献
    相似文献
    引证文献
引用本文

于同敏,张拯恺,段春争.注塑工艺参数和超声外场对聚丙烯制件结晶结构的影响[J].高分子材料科学与工程,2019,35(10):124-130. Tongmin Yu, Zhengkai Zhang, Chunzheng Duan. Influence of Injection Process Parameters and Ultrasonic Field on Crystalstructure of Polypropylene Parts[J]. Polymer Materials Science & Engineering,2019,35(10):124-130.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2019-12-03
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司