离子液体中再生纤维素纤维的制备及表征
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

国家林业公益性科研专项(201504602-2)


Preparation and Characterization of Regenerated Cellulose Fibers in Ionic Liquid
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    以离子液体为溶剂,采用干喷-湿纺法制备再生纤维素纤维,通过正交设计和系统试验考察了气隙长度、喷头拉伸比、凝固浴浓度和凝固浴温度等工艺参数对再生纤维素纤维力学性能的影响,探究了该体系的最佳纺丝工艺条件,并对此条件下的产物进行表征分析。结果表明,对于该体系,纺丝工艺参数中凝固浴浓度和拉伸比对纤维的拉伸强度、初始模量的影响较大,凝固浴温度对纤维断裂伸长影响较大。此外,最佳工艺条件下制备的再生纤维素纤维具有较高的结晶度,较好的热稳定性及光洁的表面形态。

    Abstract:

    The regenerated cellulose fibers were made by the dry-wet spinning method using ionic liquid as solvent. In this work, the influence of spinning parameters including length of air layer, draw down ratio, coagulation bath concentration and coagulation bath temperature on the mechanical properties of the cellulose fibers were investigated via orthogonal design and experiments, and then the best spinning process conditions were found. The characterizations of the fibers were also analyzed. The results show that the tensile strength and the initial modulus of the regenerated cellulose fibers are mainly influenced by coagulation bath concentration and draw down ratio, and the elongation at break of the regenerate cellulose fibers is mainly influenced by the coagulation bath temperature. The fibers have higher crystallinity, better thermal stability under appropriate technological conditions, and the surface morphology is smooth.

    参考文献
    相似文献
    引证文献
引用本文

马继玮,姜泽明,高 鑫,张力平.离子液体中再生纤维素纤维的制备及表征[J].高分子材料科学与工程,2019,35(10):176-182. Jiwei Ma, Zeming Jiang, Xin Gao, Liping Zhang. Preparation and Characterization of Regenerated Cellulose Fibers in Ionic Liquid[J]. Polymer Materials Science & Engineering,2019,35(10):176-182.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2019-12-03
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司