微结构塑件的注塑充填尺度效应
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

国家自然科学基金资助项目(51475395);西南科技大学博士基金(13zx7153)


Scale Effect of Injection Filling for Microstructure Plastic Parts
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    微尺度聚合物熔体流动具有明显的尺度效应,模具温度和注射速率是微注塑充填流动的关键影响因素。文中采用微细电火花铣削技术设计分别制造了一模八腔的带有200 μm和300 μm微孔的注塑模具。以聚丙烯(PP)进行单因素充模流动工艺实验,研究了模具温度和注射速率对直径为200 μm和300 μm微圆柱充填高度影响规律。结果表明,当模具温度为30 ℃和注射速率为60%时,直径200 μm微圆柱孔的充填高度小于直径300 μm微圆柱孔的充填高度,且Ⅰ型腔的微圆柱充填高度大于Ⅱ的充填高度。随着模具温度升高和注射速率增加,2种微孔充填高度差在减小,Ⅰ型腔和Ⅱ型腔之间的充填高度差值也在减小。可见,升高模具温度和增加注射速率可以减少微尺度效应对微圆柱孔充填高度的影响,同时,还可以减小流动不平衡程度。

    Abstract:

    Micro-scale polymer melt flow has obvious scale effect. Mold temperature and injection rate are the key factors affecting micro-injection filling flow. The micro electrical discharge machining (EDM) milling technology was used to design the injection molds with a eight-cavity mold with various diameter holes ranging from 200 μm to 300 μm. Polypropylene (PP) was used to carry out single factor filling flow experiments. The effects of mold temperature and injection rate on filling height of micro-cylinders with diameters of 200 μm and 300 μm were studied. The results show that the filling height of micro-cylindrical holes with the diameter of 200 μm is less than that of micro-cylindrical holes with the diameter of 300 μm, and the filling height of micro-cylindrical holes with cavity I is higher than that of cavity II when the mold temperature is 30 ℃ and injection rate is 60%. With the increase of mould temperature and injection rate, the difference of filling height between the two kinds of micro-holes decreases, and the difference of filling height between the cavity I and the cavity II decreases. It can be seen that increasing mold temperature and injection rate can reduce the influence of micro-scale effect on filling height of micro-cylindrical holes, and at the same time, it can also reduce the degree of flow imbalance.

    参考文献
    相似文献
    引证文献
引用本文

邓爱林,薛 松,徐 斌.微结构塑件的注塑充填尺度效应[J].高分子材料科学与工程,2020,36(3):85-95. Ailin Deng, Song Xue, Bin Xu. Scale Effect of Injection Filling for Microstructure Plastic Parts[J]. Polymer Materials Science & Engineering,2020,36(3):85-95.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2020-05-14
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司