塑料微管气辅挤出中内气垫层气体的影响
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

国家自然科学基金资助项目(51403615,51863014,51663001,51763011)


Influence of Gas in the Inner Gas Layer on Gas-Assisted Extrusion of Plastic Micro-Tube
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    塑料微管尺寸极小,挤出时熔体离开口模时仍为熔融态,内气垫层气体离开口模后仍在微管腔内流动,会对微管成型产生影响。为此,建立了考虑塑料微管腔内气体流动的双气垫层气辅挤出模型,重点分析内气垫层气体离开口模后的流动对微管成型的影响。通过对管壁内外双层气垫层作用下微管挤出成型过程的有限元数值模拟和实验研究,得到了微管型貌、速度、压力降和第一法向应力差等分布。分析表明,当气体离开口模后,由于外气垫层气体离开口模后进入空气中瞬间减压,而内气垫层气体离开口模后进入微管腔内,仍有一定压力,致使微管管壁内侧气压较外侧气压更大,从而导致微管直径逐渐增大;熔体在口模出口处及出口模后,均有第一法向应力差的产生,分析表明,这与微管形貌、壁厚、流速及压力降等的变化存在较大的关联。考虑了微管腔内气体流动的几何模型更符合实验中当气体压力较大时微管壁面出现凹凸波纹现象,口模出口处微管管壁迅速变薄及口模外部微管管壁逐渐变薄的现象。

    Abstract:

    The size of the plastic micro-tube is extremely small. When the melt exits the die during extrusion, it is still in molten state. The gas in the inner gas layer still flows in the cavity of micro-tube after leaving the die, which will affect the micro-tube forming. Therefore a double layer gas-assisted extrusion model considering the gas flow in the cavity of plastic micro-tube was established, focused on the influence of the flow of the gas in the inner gas layer after leaving the die on the micro-tube forming. Through the finite element numerical simulation and experimental research on the micro-tube extrusion process under the double gas layer inside and outside the tube wall, the micro-tube shape, velocity, pressure drop and first normal stress difference were obtained. The analysis show that when the gas leaves the die, the gas in the external gas layer enters the air and then decompresses instantaneously, and the gas in the inner gas layer enters the cavity of micro-tube after leaving the die, and there is still a certain pressure. The inner air pressure of the wall is larger than the outer air pressure, which leads to the diameter of the micro tube gradually increasing. The first normal stress difference is generated at the exit of the die and after the exit of the die, and the analysis shows that there is a large correlation between the micro-tube morphology, wall thickness, flow velocities and pressure drop. The geometric model considering gas flow in the cavity of micro-tube is more in line with the phenomenon that the wall surface of the micro-tube is corrugated, the wall of the micro-tube at the exit of the die is rapidly thinned and the wall of the micro-tube after the exit of the die is gradually thined when the gas pressure is large.

    参考文献
    相似文献
    引证文献
引用本文

刘同科,黄兴元,柳和生,任 重,罗 成,王都阳.塑料微管气辅挤出中内气垫层气体的影响[J].高分子材料科学与工程,2020,36(4):75-86. Tongke Liu, Xingyuan Huang, Hesheng Liu, Zhong Ren, Cheng Luo, Duyang Wang. Influence of Gas in the Inner Gas Layer on Gas-Assisted Extrusion of Plastic Micro-Tube[J]. Polymer Materials Science & Engineering,2020,36(4):75-86.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2020-06-05
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司