电子束固化制备聚丙烯/铝箔复合膜
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

河南省科学院杰青人才培养(190415007)


Preparation of Polypropylene/Al Foil Laminate by Electronic Beam Curing Technology
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    将电子束(EB)固化技术应用于聚丙烯/铝箔复合膜的制备,研究了胶黏剂配方中基体树脂、单体、添加剂对胶层的固化及黏结性能的影响;通过胶层红外光谱分析了黏结反应机理;通过凝胶含量、剥离力测试优选出EB固化胶黏剂配方,并制备出了具有良好黏结强度的复合膜。采用脂肪族和芳香族聚氨酯丙烯酸酯混合树脂,添加2%的聚多异氰酸酯作为胶黏剂,在25 kGy的辐照剂量下,固化后胶层凝胶含量达97%,复合膜层间剥离力为9 N/15 mm。

    Abstract:

    Electronic beam curing technology was applied in preparation of polypropylene/Al foil laminate. The adhesive layer bonding performance was measured by gel content and T-style peel strength test. The relationship between adhesive formula (resin, monomer, additive) and bonding performance was investigated. The adhesive reaction mechanism was studied by infrared spectrum analysis (FT-IR). A polypropylene/Al foil laminate was prepared with the optimizd adhesive formula and radiation dose: the EB irradiation dose is 25 kGy, aliphatic and aromatic polyurethane acrylate (PUA) are mixed and 2% polyisocyanate (PMDI) is added. The gel content of the composite film could exceed 90% and the T-style peeling force reaches 9 N/15 mm.

    参考文献
    相似文献
    引证文献
引用本文

赵 康, 赵红英, 崔国士, 高俊娜, 束兴娟, 樊 茹.电子束固化制备聚丙烯/铝箔复合膜[J].高分子材料科学与工程,2020,36(8):29-35. Kang Zhao, Hongying Zhao, Guoshi Cui, Junna Gao, Xingjuan Shu, Ru Fan. Preparation of Polypropylene/Al Foil Laminate by Electronic Beam Curing Technology[J]. Polymer Materials Science & Engineering,2020,36(8):29-35.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2020-10-22
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司