高绝缘导热环氧塑封料的制备及表征
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

安徽省科技重大专项(17030901076)


Preparation and Characterization of High Insulation and Thermal Conductive Epoxy Molding Compound
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    采用硅烷偶联剂γ-氨丙基三乙氧基硅烷 (KH550) 对硅微粉进行表面改性,并利用傅里叶变换红外光谱、热重分析仪进行表征。结果表明,KH550在硅微粉上的接枝率为0.4%。与未改性硅微粉填充的环氧塑封料相比,改性硅微粉填充的环氧塑封料的导热系数、体积电阻率、介电强度、熔融指数明显提高。当填充质量分数为80%时,改性硅微粉填充环氧塑封料的导热系数、体积电阻率、介电强度,熔融指数分别达到1.55 W/(m·K),4.2×1015 Ω·cm,26.2 kV/mm,7.4 g/10 min。

    Abstract:

    Silicon micropowders (SiO2) were surface modified by KH550. The modified SiO2 was characterized by infrared spectroscopy and thermal gravimetric analyzer, and the grafting rate of KH550 is 0.4%. The thermal conductivity, volume resistivity, dielectric strength and melt index of the modified SiO2 filling epoxy molding compound are considerably higher than those of the pristine SiO2 filling epoxy molding compound. When the filling mass fraction is 80%, the thermal conductivity, volume resistivity, dielectric strength and melt index of the modified SiO2 filling epoxy molding compound reach 1.55 W/(m·K), 4.2×1015 Ω·cm, 26.2 kV/mm, 7.4 g/10 min, respectively.

    参考文献
    相似文献
    引证文献
引用本文

张建英, 徐卫兵, 周正发, 马海红, 任凤梅.高绝缘导热环氧塑封料的制备及表征[J].高分子材料科学与工程,2020,36(9):111-114. Jianying Zhang, Weibing Xu, Zhengfa Zhou, Haihong Ma, Fengmei Ren. Preparation and Characterization of High Insulation and Thermal Conductive Epoxy Molding Compound[J]. Polymer Materials Science & Engineering,2020,36(9):111-114.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2020-11-13
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司