石墨烯改性聚甲基丙烯酸甲酯复合材料的制备及性能
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

国家自然科学基金石油化工联合基金A类项目(U1762218)


Preparation and Properties of Graphene-Modified Polymethyl Methacrylate Composites
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    聚甲基丙烯酸甲酯(PMMA)具有易加工、价格低廉及透光率好等优点,但在高温下的力学性能较差,阻碍了其在高温环境中的应用。文中以PMMA为基体,通过添加石墨烯(GR)作为增强材料,制备了石墨烯改性的PMMA/GR复合材料,并考察了石墨烯对PMMA热分解性能、玻璃化转变温度及力学性能的影响。研究发现,与PMMA相比,PMMA/GR复合材料的热分解温度略微降低,玻璃化转变温度最高可以达到109.0 ℃,比纯PMMA高4.7 ℃,在100 ℃的弹性模量、断裂应力和断裂伸长率最高可以达到535.8 MPa,12.6 MPa和186.9%,分别是纯PMMA的2.5倍、2.2倍和3.3倍,在120 ℃的弹性模量、断裂应力和断裂伸长率最高可以达到25.0 MPa,4.5 MPa和254.7%,分别是纯PMMA的6.4倍、2.4倍和1.9倍。

    Abstract:

    Polymethyl methacrylate (PMMA) has the advantages of easy processing, low price, and good light transmittance, but its poor mechanical properties at high temperature hinder its application in high temperature environment. In this paper, PMMA was used as modified matrix and graphene (GR) was added as reinforcing material, then PMMA/GR composites were prepared. The effects of graphene on PMMA thermal decomposition performance, glass transition temperature and mechanical properties were compared and analyzed. It is found that, compared with PMMA, the thermal decomposition temperature of PMMA/GR composite material is slightly reduced, and the glass transition temperature is up to 109.0 ℃, which is 4.7 ℃ higher than that of pure PMMA. The elastic modulus, breaking strength and break strain are up to 535.8 MPa, 12.6 MPa and 186.9% at 100 ℃, which are 2.5, 2.2 and 3.3 times higher than those of pure PMMA, respectively. The elastic modulus, breaking strength, and break strain at 120 ℃ can reach up to 25.0 MPa, 4.5 MPa and 254.7%, which are 6.4, 2.4 and 1.9 times of pure PMMA, respectively.

    参考文献
    相似文献
    引证文献
引用本文

吴殿国, 郭 娜, 殷鸿尧, 冯玉军.石墨烯改性聚甲基丙烯酸甲酯复合材料的制备及性能[J].高分子材料科学与工程,2020,36(10):1-7. Dianguo Wu, Na Guo, Hongyao Yin, Yujun Feng. Preparation and Properties of Graphene-Modified Polymethyl Methacrylate Composites[J]. Polymer Materials Science & Engineering,2020,36(10):1-7.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2020-12-15
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司