紫外光本体法制备丙烯酸酯压敏胶的合成与表征
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

天津市科技计划项目(17YFCZZC00280);国家自然科学基金资助项目(51573037)


Preparation and Characterization of Acrylate Pressure Sensitive Adhesives via UV Bulk Polymerization
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    以丙烯酸酯为原料,采用紫外光引发聚合制备具有一定黏度的预聚物,随后采用光和热双重固化的方法,获得本体法聚丙烯酸酯压敏胶,考察了二官能度异氰酸酯交联剂用量对其压敏性能的影响。旋转黏度计测定了预聚物的黏度;索氏提取法测定产物的凝胶含量;通过凝胶渗透色谱表征了可溶部分聚合物的相对分子质量;动态力学热分析研究了聚合物的黏弹性,并测定该压敏胶的性能,包括初黏力、剥离力和持黏强度。结果表明,丙烯酸酯单体全部参与反应;当丙烯酸羟乙酯(HEA)含量为10%、丙烯酸丁酯(BA)与丙烯酸(AA)的质量比为92∶8、异氰酸酯(KL-1202)含量为0.1%时,压敏胶的综合性能最好。

    Abstract:

    The acrylate prepolymers were prepared by bulk polymerization using UV irradiation and then cured by UV photoinitiation and thermo-crosslinking process to get the pressure sensitive adhesives (PSAs). The influence of difunctional isocyanate content on the structures and properties of the resulting PSAs was discussed. The viscosity of the prepolymer was measured by rotational viscometer. The gel content was examined by Soxhlet extraction and the molecular weight of soluble parts of PSAs was characterized by GPC. The molecular motion of the polymer was determined by dynamic mechanical analysis (DMA). Moreover, fundamental adhesive performance involving loop tack force, peel force and shear resistance of PSAs were measured. The results show that all acrylate monomers are participated in the polymerization. When the content of 2-hydroxyethyl acrylate (HEA) is 10%, the mass ratio of butyl acrylate (BA) and acrylic acid (AA) is 92∶8, and the content of difunctional isocyanate (KL-1202) is 0.1%, the optimal adhesive properties of polyacrylic PSAs could be obtained.

    参考文献
    相似文献
    引证文献
引用本文

朱梦璐, 辛峻伟, 李国华, 谢延林, 解一军, 瞿雄伟.紫外光本体法制备丙烯酸酯压敏胶的合成与表征[J].高分子材料科学与工程,2020,36(10):51-54. Menglu Zhu, Junwei Xin, Guohua Li, Yanlin Xie, Yijun Xie, Xiongwei Qu. Preparation and Characterization of Acrylate Pressure Sensitive Adhesives via UV Bulk Polymerization[J]. Polymer Materials Science & Engineering,2020,36(10):51-54.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2020-12-15
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司