微发泡工艺与材料配比对聚己内酯/聚乳酸共混材料微发泡行为的影响
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

国家自然科学基金资助项目(11372287);河南省科技攻关项目(国际科技合作)(172102410061)


Effect of Foaming Process and Material Proportion on Microcellular Foaming Behavior of Polycaprolactone/Polylactic Acid Blends
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    可生物降解聚合物多孔支架已成为组织工程的研究热点。文中采用超临界CO2微发泡技术,对聚乳酸(PLA)与聚己内酯(PCL)共混材料进行发泡,并分析了发泡工艺、材料配比对PCL/PLA共混体系泡孔形态的影响。实验结果表明,随着保压压力的升高,泡孔直径减小、泡孔密度增加;随着发泡温度的升高,泡孔直径增大、泡孔密度减小;随着保压时间的延长,泡孔直径增大、泡孔密度略有降低,最终趋于稳定。泡孔直径和泡孔密度决定着开孔度的大小。随着PLA含量的增加,PCL/PLA共混体系的泡孔密度增大,泡孔直径减小。

    Abstract:

    Biodegradable polymer porous scaffolds have become the research focus of tissue engineering. The microcellular materials of polylactic acid (PLA) and polycaprolactone (PCL) blends were fabricated and investigated through supercritical carbon dioxide foaming technology. The influence of process parameters and material proportions on the cell morphology was analyzed. The SEM results indicate that the increase of saturation pressure leads to the decrease of cell size and the increase of cell density. With the increase of saturation temperature, the average cell size increases, the cell density decreases significantly. With the increase of saturation time, the average cell size increases, the cell density decreases slightly, and both of them tend to be stable completely. The open-cell content depends on the comprehensive effect of average cell size and cell density. With the increase of PLA content of the PCL/PLA blends, the cell density increases, and the average cell size decreases.

    参考文献
    相似文献
    引证文献
引用本文

王利霞, 周 露, 富学宇, 王东方, 赵幸一, 周诣平, 李 倩, 申长雨.微发泡工艺与材料配比对聚己内酯/聚乳酸共混材料微发泡行为的影响[J].高分子材料科学与工程,2020,36(12):1-6. Lixia Wang, Lu Zhou, Xueyu Fu, Dongfang Wang, Xingyi Zhao, Yiping Zhou, Qian Li, Changyu Shen. Effect of Foaming Process and Material Proportion on Microcellular Foaming Behavior of Polycaprolactone/Polylactic Acid Blends[J]. Polymer Materials Science & Engineering,2020,36(12):1-6.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2021-03-25
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司