具有规则微结构表面聚丙烯塑件的超声模压粉末成型
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

国家自然科学基金资助项目(51971150,51605304,51871157);广东省自然科学基金资助项目(2016A030310036);深圳市科技研发资助项目(JSGG20190219152602381);深圳大学青年教师科研启动项目(2017034)


Ultrasonic Powder Molding of Polypropylene Parts with Regular Micro-Structured Surfaces
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    利用自制的组合式模具,通过超声模压粉末成型工艺,制得形状尺寸可控的聚丙烯微塑件,成功复制了模芯表面的微沟槽阵列结构。设计单因素实验,研究了超声能量、焊接压力、保压时间对聚丙烯微结构塑件成型的影响。结果表明,适当增加超声能量与焊接压力,可有效提高熔体的填充能力。当超声能量为1000 J、焊接压力为115 kPa、保压时间为8 s时,所制得的微结构塑件具有较好的表面形貌复制率。差示扫描量热和X射线衍射分析表明,超声能量的增加不会改变聚丙烯的晶体结构;随着超声能量的增加,微结构塑件的结晶度降低、晶粒细化。

    Abstract:

    The PP micro-structured parts with controllable shape and size were fabricated by the modular mold and micro ultrasonic powder molding(micro-UPM). The micro-structure on the surface of the mold core was successfully replicated. Single-factor experiments were designed to investigate the effects of ultrasonic energy, welding pressure, and holding time on the molding of PP micro-structured parts. The results show that the increase of ultrasonic energy or welding pressure is beneficial to improving the filling capacity of the melt. Micro-structured parts with good surface morphology replication rates are fabricated at an ultrasonic energy of 1000 J, a welding pressure of 115 kPa and, a holding time of 8 s. DSC and XRD analysis show that the increase in ultrasound energy does not change the PP crystal structure, the crystallinity of the micro-structured parts decreases, the grains are refined.

    参考文献
    相似文献
    引证文献
引用本文

刘永旌, 马 将, 龚 峰, 徐 斌, 梁 雄.具有规则微结构表面聚丙烯塑件的超声模压粉末成型[J].高分子材料科学与工程,2021,37(2):102-107. Yongjing Liu, Jiang Ma, Fong Gong, Bin Xu, Xiong Liang. Ultrasonic Powder Molding of Polypropylene Parts with Regular Micro-Structured Surfaces[J]. Polymer Materials Science & Engineering,2021,37(2):102-107.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2021-05-06
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司