超临界二氧化碳辅助挤出制备微孔醋酸纤维素
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

装备预研重点实验室基金(6142603190210);特种能源材料教育部重点实验室(南京理工大学)开放基金(2019SEM05)


Microcellular Cellulose Diacetate Foaming with Supercritical Carbon Dioxide in Extrusion Process
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    为了连续化制备泡孔结构良好的微孔二醋酸纤维素(CDA)材料,采用超临界二氧化碳(SC-CO2)辅助CDA挤出发泡,通过扫描电镜对微孔CDA材料断面形貌进行了观测,研究了CO2注气量、螺杆转速和溶剂比对CDA泡孔形貌的影响,结果显示,随着CO2注气量增加,泡孔密度从9.3×107 cm-3增加至1.04×1011 cm-3,平均泡孔直径从10.06 μm减小至1.16 μm;随着螺杆转速的提高,压降速率显著增加,泡孔密度从6.6×107 cm-3增加到了9.12×1010 cm-3,泡孔直径从28.1 μm减小到了0.88 μm;随着醇酮溶剂用量的增加,泡孔密度降低,并出现了泡孔合并现象。采用SC-CO2辅助挤出发泡技术可以制备出含有致密泡孔结构的微孔CDA材料。

    Abstract:

    In order to prepare microporous cellulose diacetate (CDA) materials with complete cell structure continuously, supercritical carbon dioxide (SC-CO2) was used to assist CDA extrusion foaming, and the cross-sectional morphology of the microporous CDA materials was observed by scanning electron microscope. The effects of CO2 gas injection, screw speed and solvent ratio on CDA cell morphologies were studied. The results show that with the increase of CO2 gas injection, the cell density is increased from 9.3×107 cm-3 to 1.04×1011 cm-3. The average cell diameter is decreased from 10.06 μm to 1.16 μm. With the increase of screw speed, the pressure drop rate is increased significantly, the cell density is increased from 6.6×107 cm-3 to 9.12×1010 cm-3, and the cell diameter from 28.10 μm is reduced to 0.88 μm. With the increase of the amount of solvent, the cell density is decreased, and the phenomenon of cell merger appear. Microporous CDA materials with dense cell structure can be prepared by SC-CO2 assisted extrusion foaming technology.

    参考文献
    相似文献
    引证文献
引用本文

熊 奥, 阮 建, 丁亚军, 应三九.超临界二氧化碳辅助挤出制备微孔醋酸纤维素[J].高分子材料科学与工程,2021,37(3):24-31. Ao Xiong, Jian Ruan, Yajun Ding, Sanjiu Ying. Microcellular Cellulose Diacetate Foaming with Supercritical Carbon Dioxide in Extrusion Process[J]. Polymer Materials Science & Engineering,2021,37(3):24-31.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2021-06-08
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司