玻纤增强聚丙烯多腔微注塑中纤维取向与流动偏移
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

福建省教育厅科技计划(JA12197);福建省科技计划引导性(重点)项目(2016H0023)


Fibre Orientation and Flow Deviation of Glass Fibre Reinforced Polypropylene During Multi-Cavity Micro-Injection Moulding
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    采用3D模拟技术和各项异性旋转扩散-诱导应变闭合(ARD-RSC)等模型以及集成式热电偶传感器温度测量系统和可视化全息示踪技术,对多型腔微注塑成型过程中玻纤增强聚丙烯(GFRPP)熔体在流道中的纤维取向、温度和流动速度偏移现象进行模拟和分析。结果表明,低速注射时,GFRPP熔体中纤维取向明显,流道表层区域的纤维取向程度大于芯层区域的纤维取向,存在着明显的、不对称的表层-芯层-表层结构,纤维取向加剧了塑料熔体前沿温度与流动速度的向下偏移。高速注射时,纤维取向仍然存在不对称的表层-芯层-表层结构,但比低速注射时不明显得多,纤维取向对熔体前沿高温区和流动速度向下侧偏移幅度的影响也较低速注射时更大。即GFRPP熔体在不同注射速度下熔体的流动速度、流动状态、温度变化相互作用与影响,使得熔体的纤维取向,流动速度、温度分布产生偏移,导致流道系统和型腔充型不均衡。

    Abstract:

    Three-dimensional (3-d) simulation technology, an anisotropic rotary diffusion-reduced strain closure (ARD-RSC) model, and a temperature measuring system equipped with integrated thermocouple sensors, and visual holographic tracer technique were used. On this basis, the fibre orientation and deviations of the temperature and flow velocity distributions of glass fibre reinforced polypropylene (GFRPP) melts in the runners during multi-cavity micro-injection moulding were simulated and analyzed. The results show that at a low injection rate, GFRPP melts present a significant fibre orientation; the degree of fibre orientation in the surface area is greater than that in the core of the runners, forming an asymmetric surface-core-surface structure. The fibre orientation aggravates the downward deviation of the temperature and flow velocity distributions of the GFRPP melt flow fronts. At a high injection rate, an asymmetric surface-core-surface structure persists due to the fibre orientation; however, the structure is less significant than that formed at a low injection rate. The effects of the fibre orientation on the downward deviation amplitude of the high-temperature zone and flow velocity distribution of the melt flow fronts are greater than that at a low injection rate. This means that the changes of the flow velocity, flow state, and temperature of GFRPP melts interact at different injection rates, which causes the fibre orientation of the melts to appear and their flow velocity and temperature distributions to deviate. As a result, it leads to unbalanced filling in the runner system and cavities.

    参考文献
    相似文献
    引证文献
引用本文

郭幼丹, 吴春笃.玻纤增强聚丙烯多腔微注塑中纤维取向与流动偏移[J].高分子材料科学与工程,2021,37(7):95-102. Youdan Guo, Chundu Wu. Fibre Orientation and Flow Deviation of Glass Fibre Reinforced Polypropylene During Multi-Cavity Micro-Injection Moulding[J]. Polymer Materials Science & Engineering,2021,37(7):95-102.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2021-09-27
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司