可用作3D打印基材的聚(乳酸-乙烯基吡咯烷酮)材料的制备与性能
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

国家重点研发计划(2017YFE0102600)


Preparation and Properties of Poly(L-lactide-b-N-vinyl-2-pyrrolidone) Materials for 3D Printing Substrates
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    采用丙三醇开环聚合左旋丙交酯(L-LA),合成了三臂乳酸预聚物(PLLA 3),通过与封端剂富马酸单乙酯(FAME)的酯化反应,成功地合成光敏性三臂乳酸预聚物(PLLA 3-FAME)。将PLLA 3-FAME与反应性稀释剂N-乙烯基吡咯烷酮(NVP)和光引发剂Irgacure 2959,混合调制成光敏性聚(乳酸-乙烯基吡咯烷酮)树脂,经紫外光固化后成功成型,得到聚(乳酸-乙烯基吡咯烷酮)材料,并对材料结构和性能进行了表征测试。结果表明,较材料PLLA相比,聚(乳酸-乙烯基吡咯烷酮)材料的亲水性、拉伸强度和降解速度均有显著提升。水接触角由91°±2°下降至75°±4°,吸水率由0.43%提升至35%;拉伸强度和延伸率分别由28 MPa,3.82%提升至77 MPa,11.35%;24周内的降解速度由未发生降解提升至质量损失27.57%。该材料可作为3D打印基材,可用于定制要求和组织工程的材料领域。

    Abstract:

    Using glycerol ring-opening polymerization of L-lactide (L-LA), a three-armed PLLA oligomer (PLLA 3) was synthesized, and through esterification reaction with the capping agent monoethyl fumarate (FAME), successfully synthesized the three-armed photosensitive FAME-functionalized PLLA oligomer (PLLA 3-FAME). PLLA 3-FAME, reactive diluent N-vinylpyrrolidone (NVP) and photoinitiator Irgacure 2959 were mixed to prepare a photosensitive poly(L-lactide-b-N-vinyl-2-pyrrolidone) resin, which was cured by ultraviolet light and successfully formed to obtain the poly(L-lactide-b-N-vinyl-2-pyrrolidone) material, and the structure and properties of the material were characterized and tested. The results show that compared with PLLA, the hydrophilicity, tensile strength and degradation rate of poly(L-lactide-b-N-vinyl-2-pyrrolidone) are significantly improved: the water contact angle decreases from 91°±2° to 75°±4°, the water absorption is increased from 0.43% to 35%, the tensile strength and elongation are increased from 28 MPa, 3.82% to 77 MPa, 11.35%, respectively, and the degradation rate within 24 weeks is increased from no degradation to 27.57% of mass loss. The material can be used as 3D printing substrate and be widely used in the fields of customization requirements and tissue engineering.

    参考文献
    相似文献
    引证文献
引用本文

王 勇, 胡少东, 牛亚鹏, 张东豫, 罗灿选, 郝 辉, 唐中岚, 李 赛.可用作3D打印基材的聚(乳酸-乙烯基吡咯烷酮)材料的制备与性能[J].高分子材料科学与工程,2021,37(9):1-7. Yong Wang, Shaodong Hu, Yapeng Niu, Dongyu Zhang, Canxuan Luo, Hui Hao, Zhonglan Tang, Sai Li. Preparation and Properties of Poly(L-lactide-b-N-vinyl-2-pyrrolidone) Materials for 3D Printing Substrates[J]. Polymer Materials Science & Engineering,2021,37(9):1-7.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2021-12-11
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司