马来酸二丁酯接枝高密度聚乙烯及其在粘接树脂中的应用
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:


Grafting High Density Polyethylene with Dibutyl Maleate and Its Application in Adhesive Resin
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    以马来酸二丁酯(DBM)为单体、无味过氧化二异丙苯(BIBP)为引发剂、高密度聚乙烯(HDPE)为基体树脂,通过反应挤出制备相容剂HDPE-g-DBM。研究单体和引发剂浓度、配比、反应温度及螺杆转速对相容剂熔体质量流动速率(MFR)和接枝率(GD)的影响。通过复配相容剂和聚烯烃树脂,研究其在粘接树脂中的应用。采用熔体流动速率仪、傅里叶红外光谱等对相容剂进行了表征和分析;使用万能试验机和热变形维卡软化点试验机检测粘接树脂力学性能和维卡软化点。结果表明,在BIBP引发作用下,DBM可以接枝到HDPE上,当DBM的质量分数为2%、BIBP的质量分数为0.14%时,相容剂的MFR为2.07 g/10 min、GD为1.9%;粘接树脂中加入20%的相容剂后,粘接树脂各项性能均能符合给水用钢丝网增强聚乙烯复合管道对于粘接树脂的参数要求。

    Abstract:

    Using dibutyl maleate (DBM) as monomer, odorless dicumyl peroxide (BIBP) as initiator and high-density polyethylene (HDPE) as matrix resin, the compatibilizer HDPE-g-DBM was prepared by reactive extrusion. The effects of monomer and initiator concentration and ratio, reaction temperature and screw speed on the melt mass flow rate (MFR) and grafting rate (GD) of the compatibilizer were studied. Through compounding compatibilizer and polyolefin resin, its application in adhesive resin was studied. The compatibilizer was characterized and analyzed by melt flow rate meter, Fourier infrared spectroscopy (FT-IR), etc. The universal testing machine and thermal deformation Vicat softening point tester were used to detect the mechanical properties and Vicat softening point of the adhesive resin. The results show that DBM can be grafted onto HDPE under the initiation of BIBP. When the mass fraction of DBM is 2% and mass fraction of BIBP is 0.14%, the MFR of the compatibilizer is 2.07 g/10 min and the GD is 1.9%; After adding 20% of the compatibilizer to the resin, the performance of the bonding resin can meet the parameter requirements of bonding resin for steel mesh reinforced polyethylene composite pipe for water supply.

    参考文献
    相似文献
    引证文献
引用本文

刘光远, 王丰武, 汪义辉, 翟前超, 张忠洁, 郑德宝, 陈祥迎.马来酸二丁酯接枝高密度聚乙烯及其在粘接树脂中的应用[J].高分子材料科学与工程,2021,37(12):17-23. Guangyuan Liu, Fengwu Wang, Yihui Wang, Qianchao Zhai, Zhongjie Zhang, Debao Zheng, Xiangying Chen. Grafting High Density Polyethylene with Dibutyl Maleate and Its Application in Adhesive Resin[J]. Polymer Materials Science & Engineering,2021,37(12):17-23.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2022-04-02
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司