聚二甲基硅氧烷柔性基材上应力-激光复合制备直角微沟槽
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

国家自然科学基金资助项目(500180089);广州市基础与应用研究项目(202102020447);“攀登计划”专项基金(pdjh2021b0155)


Stress-Laser Composite Fabrication of Right-Angle Microgrooves on Polydimethylsiloxane Flexible Substrate
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    聚二甲基硅氧烷(PDMS)是一种应用广泛的柔性材料。文中在PDMS表面制备了直角微沟槽,分析了直角微沟槽的形貌。结合PDMS的柔性特点,开展了预应力下纳秒激光制备PDMS表面直角微沟槽实验。结果表明,微沟槽两侧的微裂纹随着激光扫描速度的增大(100~600 mm/s)开始出现随后逐渐变小,微沟槽的几何形貌随扫描速度发生改变,其深度最大值为43.14 μm、最小值为8.41 μm,其宽度最大值为111.41 μm、最小值为16.18 μm,且直角微沟槽的内外侧形貌存在差异;调整预应力角度可以调控微沟槽两侧微裂纹的走向、微沟槽的几何形貌和扫描路径的偏移。应力辅助是一种调控表面形貌,辅助PDMS表面微纳加工实现功能化的简便方法。

    Abstract:

    Polydimethylsiloxane (PDMS) is a widely used flexible material. In this paper, right-angled microgrooves were prepared on the surface of PDMS, and the morphologies of the right-angled microgrooves were analyzed. Combining with the flexible characteristics of PDMS, the experiment of preparing right-angle micro grooves on PDMS surface by nanosecond laser under prestress was carried out. The experimental results show that as the laser scanning speed increases (100~600 mm/s), the micro-cracks on both sides of the micro-groove begin to appear and then gradually become smaller. The geometric morphology of the micro-groove changes with the scanning speed, and the maximum width is 43.14 μm, the minimum width is 8.41 μm, the maximum width is 111.41 μm, and the minimum width is 16.18 μm, and there are differences in the morphology of the inner and outer sides of the right-angle microgroove; adjusting the prestress angle can control the direction of the microcracks on both sides of the microgrooves, the geometry of the microgrooves and the offset of the scanning path. Stress-assisted is a simple and convenient method to control surface morphology and assist PDMS surface micro-nano processing to realize functionalization.

    参考文献
    相似文献
    引证文献
引用本文

谢凯武, 李泽斌, 邓 宇, 张 璆, 钟世裕, 蔡俊劲, 常磊鑫.聚二甲基硅氧烷柔性基材上应力-激光复合制备直角微沟槽[J].高分子材料科学与工程,2022,38(3):106-112. Kaiwu Xie, Zebin Li, Yu Deng, Qiu Zhang, Shiyu Zhong, Junjin Cai, Leixin Chang. Stress-Laser Composite Fabrication of Right-Angle Microgrooves on Polydimethylsiloxane Flexible Substrate[J]. Polymer Materials Science & Engineering,2022,38(3):106-112.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2022-06-14
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司