超临界CO2辅助聚己二酸对苯二甲酸丁二醇酯/聚乳酸珠粒发泡
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

湖北省重点研发计划(2021BGD018)


Poly(butylene adipate - co - terephthalate)/Polylactic Acid Foamed Beads Prepared by Supercritical CO2
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    聚己二酸对苯二甲酸丁二醇酯(PBAT)由于其低熔体强度、低模量使其在发泡过程中易发生泡孔塌陷、收缩等问题。文中利用熔点较高的聚乳酸(PLA,175 ℃)与熔点较低的PBAT(125 ℃)在180 ℃共混后以超临界二氧化碳(scCO2)为发泡剂,采用升温法(50 ℃浸渍、130 ℃发泡)制备了不黏结的PBAT/PLA 发泡珠粒。旋转流变仪结果表明,随着PLA 含量的增加,低频下共混物的储能模量和黏度均增加;差示扫描量热仪和偏光显微镜结果表明,发泡过程中不熔的PLA 晶体与scCO2 促进了共混物的结晶;扫描电子显微镜和发泡实物图表明,随着PLA 含量的增加,共混物发泡珠粒的泡孔密度和体积膨胀率先增加后减小,平均泡孔尺寸减小。PLA 质量分数为5%时,泡孔密度最大达7.489×107 cm-3、体积膨胀率达9.47 倍、收缩率低至5.6%,发泡珠粒表面光滑。该法在不损失PBAT 降解性的基础上,通过升温法工艺并辅助少量PLA 改善PBAT 泡孔形态和抗收缩性能,为工业化生产提供了简单方法。

    Abstract:

    Poly(butylene adipate - co - terephthalate) (PBAT) is prone to bubble collapse and shrinkage during the foaming process due to its low melt strength and modulus. In this paper, PBAT/PLA foamed beads were prepared using polylactic acid (PLA, 175 ℃) with higher melting point and PBAT (125 ℃) with lower melting point at 180 ℃ used scCO2 as foaming agent, by heating- up method (impregnation at 50 ℃ and foaming at 130 ℃ ). Rotational rheometer results show that the storage modulus and viscosity of the blends increase with the increasing of PLA content. Differential scanning calorimetry and polarizing microscope results show that PLA crystals do not melt during foaming and scCO2 promotes the crystallisation of the blends. Scanning electron microscopy and foaming diagrams show that the pore density and volume expansion of the blended foamed beads increase and then decrease with the increasing of PLA content, and the average mean diameter decreases. At the PLA mass fraction of 5%, the cell density reaches the maximum of 7.489×107 cm-3, the expansion rate reaches 9.47 times, the shrinkage rate is as low as 5.6% and the surface of the foamed beads is smooth. This method provides a simple method for the industrial production by improving PBAT cell morphology and shrinkage resistance through heating up method with a small amount of PLA, without the loss of PBAT degradability.

    参考文献
    相似文献
    引证文献
引用本文

谢茂卿,杜俊威,张世豪,胡园园,刘清亭,付旭东,张荣,胡圣飞.超临界CO2辅助聚己二酸对苯二甲酸丁二醇酯/聚乳酸珠粒发泡[J].高分子材料科学与工程,2022,38(8):66-74. Maoqing Xie, Junwei Du, Shihao Zhang, Yuanyuan Hu, Qingting Liu, Xudong Fu, Rong Zhang, Shengfei Hu. Poly(butylene adipate - co - terephthalate)/Polylactic Acid Foamed Beads Prepared by Supercritical CO2[J]. Polymer Materials Science & Engineering,2022,38(8):66-74.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2022-11-02
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司