封闭聚异氰酸酯对含氟聚丙烯酸酯整理织物性能的影响
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

安徽省药监局科技创新计划(AHYJ-KJ-202006)


Effect of Blocked Polyisocyanate onWaterproof Performance of Fluorinated Polyacrylate Emulsion Finishing Fabric
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    制备了不同熔点及解封温度的封闭聚异氰酸酯交联剂(BIC)和含氟聚丙烯酸酯乳液(FPA)。利用红外光谱和透射电镜等对FPA的结构和微观形貌等进行了表征。对添加BIC的FPA乳液(BFPA)浸涂固化整理过的棉织物(BFCM)进行了静态疏水、动态喷淋、接触角、耐摩擦和耐水洗等性能测试,比较了BIC的熔点对BFCM疏水性能的影响。结果表明,随着BIC 熔点降低,其解封温度越低,BFCM的防水、耐磨、耐洗等性能均有显著提升。BIC 熔点为6.6 ℃时,其解封温度最低为75 ℃,经110 ℃处理后BFCM水接触角(WCA)可达142.9°,沾水等级可达5 级;100 ℃处理后经50 个摩擦周期和24 h 水洗后,WCA仍然分别可达132.5°和136.5°。

    Abstract:

    Blocked polyisocyanate crosslinker (BIC) and fluorinated polyacrylate emulsion (FPA) with different melting points and deblocking temperature were prepared. The chemical structure and microstructure of FPA were characterized by FT-IR and TEM. BFCM was obtained by hydrophobic treatment of cotton fabric with 1K emulsion FBPA composed of BIC and FPA. The static hydrophobicity, dynamic spray, contact angle, friction resistance and washing resistance of BFCM were tested. The effect of the melting point and deblocking temperature of BIC on the hydrophobicity of BFCM was compared. The results show that the waterproofing, wearresisting and washable properties of BFCM are improved significantly with the decrease of the melting point and deblocking temperature of BIC. When the melting point of BIC is 6.6 ℃, the lowest deblocking temperature of BIC is 75 ℃ , under the 110 ℃ treatment, the water contact angle(WCA) of BFCM can reach 142.9° and the hydrophobic grades can reach 5. After the treatment at 100 ℃ for 50 friction cycles and 24 h water washing, WCA can still reach 132.5° and 136.5°, respectively

    参考文献
    相似文献
    引证文献
引用本文

翟林明,李晓萱,孟 勋,尹 政,李鹏辉,伍胜利.封闭聚异氰酸酯对含氟聚丙烯酸酯整理织物性能的影响[J].高分子材料科学与工程,2023,39(2):36-42. Linming Zhai, Xiaoxuan Li, Xun Meng, Zheng Yin, Penghui Li, Shengli Wu. Effect of Blocked Polyisocyanate onWaterproof Performance of Fluorinated Polyacrylate Emulsion Finishing Fabric[J]. Polymer Materials Science & Engineering,2023,39(2):36-42.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2023-04-20
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司