水驱动弹头辅助共注塑工艺相间穿透机理的数值模拟
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

国家自然科学基金资助项目(52163006,52273033);江西省科技厅重点研发计划(20203BBE53065)


Numerical Simulation of Interphase Penetration Mechanism of Water-Projectile Assisted Co-Injection Molding Process
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    溢流法水驱动弹头辅助共注塑(Overflow water-projectile assisted co-injection molding,W-PACIM-O)工艺可制取双层包覆式结构的中空管件。采用数值模拟技术分析了W-PACIM-O工艺注水阶段的界面不稳定性现象、管件壁厚分布以及内层熔体和弹头穿透行为,从而掌握W-PACIM-O的相间穿透机理。模拟结果表明,W-PACIM的湍流强度相对较小,且基本无湍流漩涡,其起始段壁厚界面不稳定性现象不明显;W-PACIM管件的总残余壁厚、外层壁厚和内层壁厚更薄,壁厚波动较小;压力水驱动弹头穿透阶段,W-PACIM工艺穿透前沿速度更高,穿透更稳定。

    Abstract:

    Overflow water- projectile assisted co- injection molding(W- PACIM- O) technology can be used to manufacture hollow pipes of double-layer structure. Numerical simulation was performed to analysis the instability of water injection stage of the W-PACIM-O process, the wall thickness distribution of the pipe, the penetration behavior of the inner melt and projectile, and the interphase penetration mechanism of W-PACIM-O. It is found from the simulation results that the turbulence intensity of W-PACIM is relatively small, and there is basically no turbulence vortex, so the instability of the interface is not obvious. The total wall thickness, wall thickness of outer layer and inner layer of WPACIM pipe are thinner, the fluctuation of wall thickness is smaller; at the stage of penetration of projectile driven by pressurized water, the velocity of penetration front of W-PACIM is higher and more stable.

    参考文献
    相似文献
    引证文献
引用本文

匡唐清,张庆伟,柳和生,赖家美,胡礼彬.水驱动弹头辅助共注塑工艺相间穿透机理的数值模拟[J].高分子材料科学与工程,2023,39(4):146-153. Tangqing Kuang, Qingwei Zhang, Hesheng Liu, Jiamei Lai, Libin Hu. Numerical Simulation of Interphase Penetration Mechanism of Water-Projectile Assisted Co-Injection Molding Process[J]. Polymer Materials Science & Engineering,2023,39(4):146-153.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2023-06-15
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司