老化环境对碳纤维增强聚醚酰亚胺树脂基复合材料超声焊接头性能的影响
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

国家自然科学基金资助项目(51403129);辽宁省兴辽英才计划(XLYC1907019);辽宁省教育厅面上项目(LJKZ0171);大学生创新创业训练项目(X202110143014, S202210143012)


Effects of Aging Environment on Ultrasonic Welding Joint Properties of Carbon Fiber Reinforced Polyether Imide Resin Matrix Composites
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    超声焊接技术因其高效、环保被认为是复合材料连接的有效方式之一。复合材料超声焊接头在不同使用环境中可能会存在一定的老化效应。文中以碳纤维增强聚醚酰亚胺复合材料(CF/PEI)超声焊接头作为研究对象,采用单搭接剪切强度(LSS)和接头破坏形貌的扫描电子显微镜观察的方法对 CF/PEI 复合材料超声焊接头在高温、水煮和湿热环境中的老化性能进行了评估。研究结果表明,复合材料超声焊接头单搭接剪切强度在较高温度时(110~170 ℃)存放5 h、吸水率在1%以上及湿热环境中(30 ℃,湿度50%)存放不同时间(5~15 d)后均出现明显下降。

    Abstract:

    Ultrasonic welding is considered to be one of the effective ways to join composite materials because of their high efficiency and environmental protection. The ultrasonic welded joint of composite materials may have certain aging effect in different use environments. In this study, the ultrasonic welded joint of carbon fiber reinforced polyetherimide composite (CF/PEI) was taken as the research object. The aging performance of CF/PEI composite ultrasonic welded joint was evaluated by scanning electron microscopy (SEM) observation of single lapping shear strength(LSS) and joint failure morphology in high temperature, boiling and humid heat environment. The results show that the single lap shear strength of the ultrasonic welded joint decreases significantly after storage at a high temperature (110~170 ℃) for 5 h, water absorption above 1%, and storage in a hot and humid environment (30 ℃, humidity of 50%) for different periods (5~15 d).

    参考文献
    相似文献
    引证文献
引用本文

王 静,肖存勇,熊志国, 贾 松,李 闯,于艺家.老化环境对碳纤维增强聚醚酰亚胺树脂基复合材料超声焊接头性能的影响[J].高分子材料科学与工程,2023,39(5):98-106. Jing Wang, Cunyong Xiao, Zhiguo Xiong, Song Jia, Chuang Li, Yijia Yu. Effects of Aging Environment on Ultrasonic Welding Joint Properties of Carbon Fiber Reinforced Polyether Imide Resin Matrix Composites[J]. Polymer Materials Science & Engineering,2023,39(5):98-106.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2023-07-11
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司