原位聚合法制备连续玻璃纤维增强尼龙6复合材料的改性和性能
作者:
作者单位:

作者简介:

通讯作者:

中图分类号:

基金项目:

河北省重点研发计划(20311201D,21314401D,21371201D,21374901D,19212108D);河北省自然科学基金资助项目(E2021208036);河北省教育厅科学技术研究项目(QN2021057)


Modification and Properties of Continuous Glass Fibre Reinforced Nylon 6 Composites Prepared by In Situ Polymerisation
Author:
Affiliation:

Fund Project:

  • 摘要
  • |
  • 图/表
  • |
  • 访问统计
  • |
  • 参考文献
  • |
  • 相似文献
  • |
  • 引证文献
  • |
  • 资源附件
  • |
  • 文章评论
    摘要:

    尼龙6(PA6)树脂具有优异的性能,其连续纤维复合材料在汽车、航空航天领域具有广泛应用。但是PA6树脂熔融后黏度较高,不易对连续纤维充分浸渍,并且连续纤维与PA6的复合材料界面黏附性较差,限制了其复合材料的性能和应用。针对这些问题,文中对连续玻璃纤维增强尼龙6(CGF/PA6)复合材料开展了研究。首先,采用阴离子开环聚合制备PA6,确定了其最佳制备工艺;其次,用硅烷偶联剂KH550(AP)对连续玻璃纤维(CGF)进行改性,并对其进行了红外光谱表征;最后,通过原位聚合法制备了CGF/PA6复合材料,研究了AP改性对CGF/PA6复合材料力学性能的影响,并对CGF/PA6复合材料的拉伸断口进行了扫描电镜分析。结果表明,AP被键合到了CGF表面,AP改性可以增强CGF/PA6复合材料的界面黏附性,从而使CGF/PA6复合材料的拉伸强度得到改善,当AP用量为2%时,CGF/PA6复合材料的拉伸强度高达88.52 MPa,此时,复合材料的断裂伸长率最低,为4.90%。CGF/PA6复合材料的冲击强度变化不大,均在50 kJ/m2左右,说明复合材料的韧性受CGF表面改性影响较小。

    Abstract:

    Nylon 6 (PA6) resin has excellent properties and its continuous fibre composites have a wide range of applications in automotive and aerospace sectors. However, the high viscosity of PA6 resin after melting does not easily impregnate continuous fibres sufficiently, and the poor interfacial adhesion of continuous fibres and PA6 composites limits performance and applications of the composites. Aimed at these problems, continuous glass fibre reinforced nylon 6 (CGF/PA6) composites were investigated. Firstly, anionic ring- opening polymerisation was applied to prepare PA6, and the optimum preparation process was determined; secondly, continuous glass fiber (CGF) was modified with silane coupling agent KH550 (AP) and characterized by infrared spectroscopy; finally, CGF/PA6 composites were prepared by in situ polymerisation, and the effect of AP modification on the mechanical properties of CGF/PA6 composites was investigated. The tensile fractures of CGF/PA6 composites were characterized by SEM. The results show that AP was bonded to the surface of CGF and the AP modification could enhance the interfacial adhesion of CGF/PA6 composites, thus improving the tensile strength of CGF/PA6 composites. When the AP dosage is 2%, the tensile strength of CGF/PA6 composite is as high as 88.52 MPa, the elongation at break of the composite reaches the lowest level of 4.90% . The impact strength of the CGF/PA6 composites does not change much, all around 50 kJ/m2, indicating that the toughness of the composites is less affected by CGF surface modification.

    参考文献
    相似文献
    引证文献
引用本文

冯冰涛,王晓珂,张 萌,殷茂峰,张 信,孙国华,马劲松,李鹏鹏,侯连龙.原位聚合法制备连续玻璃纤维增强尼龙6复合材料的改性和性能[J].高分子材料科学与工程,2024,40(1):25-33. Bingtao Feng, Xiaoke Wang, Meng Zhang, Maofeng Yin, Xin Zhang, Guohua Sun, Jinsong Ma, Pengpeng Li, Lianlong Hou. Modification and Properties of Continuous Glass Fibre Reinforced Nylon 6 Composites Prepared by In Situ Polymerisation[J]. Polymer Materials Science & Engineering,2024,40(1):25-33.

复制
文章指标
  • 点击次数:
  • 下载次数:
  • HTML阅读次数:
  • 引用次数:
历史
  • 收稿日期:
  • 录用日期:
  • 网络出版日期:
  • 在线发布日期: 2024-03-28
  • 出版日期:
您是第      位访问者
编辑出版 :《高分子材料科学与工程》编辑部
地址 :四川省成都市一环路南一段24号 四川大学高分子研究所
电话 :028-8540 1653  E-mail:gfzclbjb@vip.sina.com
高分子材料科学与工程 ® 2026 版权所有
技术支持:北京勤云科技发展有限公司